Axle, Hubs, Tire and Wheel Recommendation for Homemade 2,000 lb Trailer
Updated 05/19/2020 | Published 04/07/2020
Products Featured in This Question
Question:
Hi, Im building a small off-road camping trailer to use with my van.... My idea was to use matching wheels and tires on the trailer so as to be carrying a second spare that can be used on either the trailer or the van.... The van has standard GM 6 on 139.5 wheels which mount on 14mm studs.... If I buy 6-lug trailer hubs, they have only 1/2inch studs, which are slightly smaller meaning they would fit a bit sloppy on the 1/2inch studs.... Is that an issue? Or will the taper of the lug nuts self-correct? The trailer will weigh around 2000# or so, so it isnt very heavy.... Could I find hubcentric rings to maybe reduce the stress on the lugs? Do I need to try some other approach? Thank you for any insight....
asked by: Gavio
Expert Reply:
While I totally understand the convenience of having a spare that can be used on either your trailer and your van, I cannot recommend using automotive tires on a trailer (or vice versa), and here's why.
ST (Special Trailer) tires are made for a specific purpose—supporting the vertical load and cornering forces of trailers, which is why their sidewalls are stiffer. P (Passenger) tires are designed with more flexible sidewalls and are made with passenger comfort and steering in mind and need to be balanced differently. Generally speaking, it's a bad idea to swap them. They simply weren't made to perform in the same way. Then there is the off-set issue where vehicles often have an offset much different than the standard zero offset of a trailer tire and wheel.
With all that in mind, below are my recommendations for building your 2,000 lb trailer:
- Dexter Trailer Axle w/ Idler Hubs - EZ-Lube - 5 on 4-1/2 Bolt Pattern - 72" Long - 2,000 lbs # 20545I-EZ-72-15
- Provider ST175/80R13 Radial Trailer Tire w/ 13" Vesper Silver Mod Wheel - 5 on 4-1/2 - LRC
Item # TA73RR
- CE Smith Offset Spare Tire Carrier # CE27310G
If you need help with wiring or other components just let me know and I will be happy to help.
Product Page this Question was Asked From
Kenda 4.80-12 Bias Trailer Tire with 12" White Wheel - 4 on 4 - Load Range C
- Trailer Tires and Wheels
- Tire with Wheel
- Bias Ply Tire
- Load Range C
- 4.80-12
- 12 Inch
- 4 on 4 Inch
- Steel Wheels - Powder Coat
- Kenda
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Q&A: Which is Better for Highway Use 4.80-12 or 5.30-12 Trailer TIres
- Q&A: What is the Pilot Diameter on a Wheel
- Q&A: What is the Difference Between Load Range B and C Trailer Tires
- Q&A: Kenda vs Taskmaster Wheel and Tire Comparison for 4.80-12 on 4 Bolt Wheel
- Q&A: How to Determine Tire Age and at What Age Should a Trailer Tire Get Replaced
- Article: Trailer Tire Sizing
- Q&A: Recommended Load Range C 4.80-12 Trailer Tire w/a 12" Galvanized Wheel
- Q&A: Can 4.80-12 Tire be Replaced with ST145/R12 Tire Using the Same Wheel
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Article: How to Tell the Weight Rating of a Trailer Axle
- Article: 7 Common Questions Everyone Has About Trailer Tires
- Article: Most Popular Wheel Bearings
- Article: Electric Brake Controller Installation on Dodge Ram Trucks to 2012
- Article: Brake Controller Installation: Starting from Scratch
Shawn
5/15/2020
Spring center to spring center appears to be about 1" wider than the mounting flange of this axle allows. There is a bolt and nut through the springs at the center, which I assume is to rest in the slots on the axle. This is a common brand boat trailer and I have not found an axle with these dimensions. 58" SC dimension seems to be a standard. How should I proceed? I can supply a photo by email.