Correct TorkLift GlowStep Revolution Scissor Steps for 2016 Highland Open Range 318RLS

Question

Question:

Would like to replace the OEM 3 step with a 4 step TorkLift GlowStep Revolution TLA8004. Does the distance from the Floor jam to the ground have a bearing on this?

asked by: James F

0

Expert Reply:

In order to use the TorkLift GlowStep Revolution Scissor Steps part # TLA8004 you will first need to confirm the width of your mounting bracket which needs to be 27-1/2". Once this is confirmed you then need determine your entry height which is measured from the ground to the top of the step well which needs to be between 32-1/2" - 44". That said, I spoke with Torklift and they were able to confirm this is what you need for a 2016 Highland Open Range 318RLS.

expert reply by: Conner L

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 3

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 4

Hey Barry, sure do! The seal that comes with the #DX87UR bearing kit is a 1.719" ID and 2.565" OD. We offer this seal individually as part #58846.

view full answer...

Answer 5

You are going to want either our Bearing Kit #BK2-100 or the Timken Kit #TMK52VR. Both of these kits will give you the inner/outer bearings and races along with a grease seal and cotter pin/D-washer for one hub. You always want to replace the race…

view full answer...

Answer 6

Hey Eric, so we do have what you need with the replacement cap part #VA55JR but the one you mentioned is smaller so it would not work for you. The cap you need is 4 inch diameter and the one you referenced is 3.75 inch.

view full answer...

Answer 7

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 8

After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub back…

view full answer...

Answer 9

In order to verify the spindle dimensions so that you can pick out the correct hub/drum you have to get exact dimensions. For that you need to use a digital caliper like part #PTW80157. For how old your trailer is this is especially important as the…

view full answer...

Answer 10

You can verify that the 10-19 grease seal included in Bearing Kit #BK2-100 is the correct one for your spindles by taking two measurements. First you want to measure the rear hub bore where the seal is inserted. The seal's outer diameter needs to…

view full answer...

Answer 11

We recommended to repack the wheel bearings on your trailer every 12 months or 12,000 miles. There is not a specific guideline as far as actually replacing the bearings. When repacking them with grease, you will also just want to check for any damage…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Correct TorkLift GlowStep Revolution Scissor Steps for 2016 Highland Open Range 318RLS

Product Page this Question was Asked From

Continue Researching