Can Handle on Bristol Waste Valve Body for RV Gray Water be Removed

Question

Question:

Our RV uses a threaded extender rod on the 1 1/2” waste valve. Does the handle on this item unscrew from the valve body, so I can connect the extender rod?

asked by: Thomas

1

Helpful Expert Reply:

Yes, the handle for the Bristol Waste Valve Body for RV Gray Water # 34439241 is threaded onto the rod so it can be removed like what you're needing.

expert reply by: Jon G

1

Joe B.

3/8/2024

I could not remove the handle until I used a set of vice grips to hold the rod. Then the handle came off smoothly.

Jon G.

3/8/2024

@JoeB Thanks for the update! Sometimes things that are designed to be easily removable can become seized over time so I'm glad to hear that you were able to get the old handle off!

Answer 1

Hi Robert; you could use the LaSalle Bristol Waste Valve #34466N11AA as a replacement but the handle will sit underneath the trailer right at the valve. Looking at the Grand Design parts site it looks like you have a 1-1/2" Valterra with a…

view full answer...

Answer 2

Yes, the handle does unscrew from the LaSalle Bristol Waste Valve part #34466N11AA. You'd be able to use your current extension.

view full answer...

Answer 3

The gray water tank valve on the Bristol Double RV Waste Valves part #34466ND13AAR can be replaced using the Bristol Waste Valve Body for RV Gray Water part #34439241 or the Valterra Bladex Waste Valve Body for RV Gray Water Tank part #T1001VP. If…

view full answer...

Answer 4

Hi Mark, welcome back! Based on your 2021 Tiffin Phaeton 37BH on a Freightliner chassis and not the PowerGlide, the most common chassis is the Freightliner XC chassis, and for that setup the confirmed anti sway bars are the Roadmaster rear bar part…

view full answer...

Answer 5

I looked up the dimensions of your High Pointe EC942K9E and it's 15 inches deep, 15.7 inches tall, and 29.9 inches wide so the Furrion Over the Range RV Convection Microwave #FMCM15SS that you referenced would easily fit in place of it and would…

view full answer...

Answer 6

I looked up the Bristol V33B2R and the correct replacement is the Bristol RV Waste Valve - Sewer Wye - Rotating - 3" and 1.5" Hubs to 3" Lug #34466N3AR which has the hub style fittings for the 3 inch and the 1.5 inch sections which…

view full answer...

Answer 7

Hello Justin. To replace your Dometic Duo-Therm 59516-531 rooftop AC unit I definitely recommend an Advent AC unit. The Advent units are made to be directly compatible with Dometic AC systems. Meaning the AC will be a plug and play install, and only…

view full answer...

Answer 8

In my experience Valterra has been MUCH easier to get in contact with and get parts from than LaSalle Bristol. Dometic is the parent company for Valterra and typically has pretty good customer service every time I've called them. It's a bit…

view full answer...

Answer 9

Thanks for reaching out, Doran! The toggle switch for your FIC-ETJ3500 is pretty unique and it looks like for a direct replacement you'll need to reach out to FIC Jack Services directly at 1-877-957-1501. You might consider looking at and…

view full answer...

Answer 10

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 11

Yes, the handle for the Bristol Waste Valve Body for RV Gray Water #34439241 is threaded onto the rod so it can be removed like what you're needing.

view full answer...

Can Handle on Bristol Waste Valve Body for RV Gray Water be Removed

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching