How Large of a Wire can I use with Large Body Chassis and Frame Clip - SWC9042-1

Question

Question:

What is the allowed diameter of the wire?

asked by: Rick P

0

Expert Reply:

I went out to the warehouse and got a measurement for you on the Large Body Chassis and Frame Clip - Qty 1
part # SWC9042-1. From the blue line in the provided picture down to the bottom of the curve there is .184" so that's going to work with wire up to the 6 AWG size.

As an example it will fall between the two measurements below

.1719 would be 11/64 or 4.365 mm
.1875 would be 3/16 or 4.762 mm

expert reply by: Randy B

0

click to enlarge

Answer 1

The Bargman 7-Pole, RV-Style Connector #50-67-103 is a 15 foot long 7-way connector for use on a trailer. It's a universal product that can be used to replace an existing 7-way or added to a newly built trailer. We offer similar products in…

view full answer...

Answer 2

Yes we do have a red version of the #CE36ZR with the part #328-003-183RR.

view full answer...

Answer 3

Both the #464600 and the #SWC9042-1 wire clips are identical. Both are 1-1/2 inches long x 1/2 inch wide with a 3/8 inch gap for wiring. We also offer a smaller clip as part #SWC9041-1, which is 1-11/16 x1/2 with a 1/4 inch gap.

view full answer...

Answer 4

We offer a few different frame clips. The Wire Frame Clip Item #464600 which is 1-1/2" long x 1/2" wide with a 3/8" gap for wiring. We also have the Medium Body Chassis and Frame Clip - Qty 1 Item #SWC9041-1 is 1-11/16" x1/2"…

view full answer...

Answer 5

It sounds like your current lights with 2 wires ground to the trailer by the mounting hardware. The One LED RV Passenger Tail Light #RVSTL0060 has three wires, the white wire is the ground, the black wire is the taillight and the green wire is for…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

How Large of a Wire can I use with Large Body Chassis and Frame Clip - SWC9042-1

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching