Diagram to Use for Installing Kodiak Caliper Rebuild kit # KDBC225KIT

Question

Question:

Do you have a video of how to rebuild it?

asked by: Frank

0

Expert Reply:

I wish we had an install video or even a manual for the Kodiak Caliper Rebuild kit # KDBC225KIT that you referenced but the best we can offer at this time is an exploded diagram that shows how all of the parts go together.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Hello Keith, Yes, you can use the Kodiak Disc Brake Caliper - Stainless Steel - 3,500 lbs to 6,000 lbs #KDBC225S (or the 225 that is not stainless) with the DeeMaxx 12" Rotor - 6 on 5-1/2 - Stainless Steel - 6,000 lbs #DE87VR. What kind of…

view full answer...

Answer 2

The side of the Silicone Dust Boot #K225BSSI, that comes with the Rebuild Kit #KDBC225KIT, with the design on the outside ring needs to face in towards the piston while the other side should face the brake pad. I have attached a photo to demonstrate…

view full answer...

Answer 3

Using compressed air is still the way to go. I have come across many instances of people using this method to push out the piston. And the best part is, it works. If you do not have an air compressor I am sure a local shop would go ahead and do it…

view full answer...

Answer 4

The seal you're looking for is the Grease Seal - Double Lip - 2.250" ID - 3.376" OD - GS-2250DL #GS-2250DL; the TRP is just the manufacturer of that particular seal, which is Tru-Ryde Products, the manufacturer of the part I've…

view full answer...

Answer 5

When you bleed the brakes on your trailer after installing the Kodiak Calipers #KDBC225DAC, you will want to start with the brake that is furthest away from the actuator. Of the two bleeder valves, you will want to use the bleeder valve that is on…

view full answer...

Answer 6

If you look at the picture I have included of Replacement Master Cylinder Filler Cap #T4480701 I would say that is coarse threaded. But regardless this cap specifically fits Titan and Dico model 60 actuators and Titan Aero 7500 actuators. If you have…

view full answer...

Answer 7

For your application I recommend using the Titan Actuator #T63FR if you have drum brakes or the Dexter DX7.5 #099-175-20 if you have disc brakes. These are rated for 7,500 lbs and fit a 2" hitch ball which should match up just fine for your 2007…

view full answer...

Answer 8

The 1-Leaf Double-Eye Spring for 6,000-lb Trailer Axles #e46SR was designed to be used without bushings so it does not come with any. A mono leaf and a multi leaf pack don't have a performance difference that's notable. They both can and work…

view full answer...

Answer 9

The 1-Leaf Double-Eye Spring for 6,000-lb Trailer Axles - 25-1/4" Long #e46SR will have the same capacity strength as a multi-leaf spring. It will replace a spring of the same length with the 3,000 lb capacity so it will work for a 6,000 lb…

view full answer...

Answer 10

In theory a single leaf spring like the part #e46SR that you referenced is going to have a better ride quality since there isn't any inner leaf friction created by the individual leaves of a larger spring pack. Depending on if your current spring…

view full answer...

Answer 11

The #e46SR spring is designed to be used without a bushing and is normally a replacement for springs on a mobile home axle. The 9/16 inch bolt will be a bit loose in this type of spring that is used without a bushing.

view full answer...

Answer 12

The only advantage you might get from using the 1-Leaf Double-Eye Spring for 6,000-lb Trailer Axles - 25-1/4" Long #e46SR instead of a handful stacked together, like the 5-Leaf #e34SR, is if you're needing to lower the height of your…

view full answer...

Diagram to Use for Installing Kodiak Caliper Rebuild kit # KDBC225KIT

Product Page this Question was Asked From

Continue Researching