Replacement Snap Ring for Dutton Lainson Swivel Jacks

Question

Question:

CAN YOU PROVIDE A NEW SNAP RING ??

asked by: Bob S

0

Expert Reply:

Yes, we have replacement snap rings for Dutton Lainson jacks like the # DL22560 that you referenced with the part # DL22672.

expert reply by: Jameson C

0

Answer 1

In order to find which snap ring you need you would have to measure the outer diameter of the snap ring bracket on your trailer frame. A part like the #DL22672 REPL Snap Ring for Swivel Trailer Jacks - 2-5/16" Inner Diameter will fit trailer…

view full answer...

Answer 2

Hi Rick, For a Fulton weld-on trailer jack that has a snap ring you can use the Fulton Boat Trailer Jack w/ Wheel - Sidewind - Swivel - 10" Lift #FTJ120W0301. I've added a link below to a video review of this jack as well if you'd like…

view full answer...

Answer 3

For your particular application, going with a single 8 inch wheel like what is on the Fulton XLT Bolt-Thru Swivel Trailer Jack #F141133 is going to be the better option. A dual wheel jack can be more beneficial on surfaces other than pavement, as a…

view full answer...

Answer 4

Thank you for providing the picture of your existing mount. This was helpful to idenfication and I have attached it to this post. As you mentioned, the 90 degree snap in holes are 3" apart from center to center. It may be helpful to note that…

view full answer...

Answer 5

Yes, the Fulton XLT Bolt-Thru Swivel Trailer Jack #F141132 that you referenced is designed to fit the same style of mounting bracket that you have in the picture you submitted. This jack will bolt right up.

view full answer...

Answer 6

I am happy to point you in the right direction. According to the online owners manual for a 2004 Ranger Trailer CF5000 Z20 boat trailer, it uses a 1200 lb Fulton Swing Jack. They do not mention any other specs, but from what I can see, they use a…

view full answer...

Answer 7

The Fulton jack part #F141132 that you referenced is a really great jack that I know you'll be happy with, but it requires the bracket part #P9012-00 to mount to a trailer which isn't the same as what you have now. So your best option is to…

view full answer...

Answer 8

The only trailer jack that will work with your existing mounting bracket and not contact the boat with a full rotation of the handle is the Fulton Bolt-Thru Swivel Marine Jack part #F1411300301. I understand this does not have the sharkskin coating…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Replacement Snap Ring for Dutton Lainson Swivel Jacks

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching