Do LED Turn Signals Need Load Resistors When Installed on a Jeep Wrangler
Question:
I just ordered some STL53RCB and MCL50AB LED trailer lights. Am I going to need resistors to let them work normally with my automotive blinker? Im mountin them in a Jeep Wrangler not a normal trailer. If I do need them, please let me know What part number I will need. Thanks!
asked by: Terry J
Expert Reply:
Yes, you will need a load resistor for each LED bulb you install on a turn signal circuit. I checked your order and it looks like you bought a total of 4 LED lights, because of that I would recommend you get two sets of LED Light Bulb Load-Resistors # DI34ZR.
I attached installation instructions and a couple pictures for this product that shows how it installs.
Products Referenced in This Question
Load Resistor Kit for LED Turn Signals - 50 Watts - 6 Ohm - Qty 2
- Accessories and Parts
- Trailer Lights
- Load-Resistor Kit
- Diamond
more information >
Miro-Flex LED Clearance or Side Marker Light w/ Reflector - Submersible - 9 Diodes - Amber Lens
- Trailer Lights
- Clearance Lights
- Rear Clearance
- Side Marker
- Round
- Recessed Mount
- Submersible Lights
- LED Light
- 2 Inch Diameter
- Amber
- Optronics
more information >
Product Page this Question was Asked From
Sealed, 4" Round, LED Trailer Stop/Turn/Tail Light, 3-Function, 10 Diode - Red w/ Clear Lens
- Trailer Lights
- Tail Lights
- Stop/Turn/Tail
- Round
- Recessed Mount
- Submersible Lights
- LED Light
- 4 Inch Diameter
- Red
- Optronics
more information >
Continue Researching
- Shop: Trailer Hitch
- Q&A: Troubleshooting Intermittent Trailer Disconnected Message with Factory Brake Controller on Ford
- Shop: Brake Controller
- Shop: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class IV - 2"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class IV - 2"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class V Commercial Duty - 2-1/2"
- Shop: Curt Echo Wireless Brake Controller - 7-Way Plug Mount w/ Bluetooth App - 1 to 2 Axle - Proportional
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Shop: Load Resistor Kit for LED Turn Signals - 50 Watts - 6 Ohm - Qty 2
- Search Results: load resistors
- Shop: Progressive Dynamics 4000 Series Mini RV Converter w/ Charge Wizard and AC/DC Distribution Panel
- Q&A: Are Load Resistors Required when Adding LED Lights to a Trailer
- Search Results: trailer turn signal lights
- Search Results: led reverse light
- Video: Optronics Lights ALEDRST1B Review
- Article: Trailer Wiring Diagrams
- Q&A: Troubleshooting Hyper Flashing Trailer Lights on Mercedes-Benz Sprinter Van
- Q&A: How to Wire the Roadmaster Single Park Light Diode # RM-690
- Q&A: Pulling a Trailer With LED Lights and the Vehicle is Reading Lamps Out
- Video: Tow Ready Wiring - Wiring Adapters - 20142 Review
- Search Results: tongue weight scale
- Q&A: Lamp Out Light Comes On in 2014 Audi A6 When Trailer Is Connected and Trailer Lights Flash Quickly
- Q&A: Recommended 6 Inch Oval LED Backup Light For Brightness
- Shop: Vehicle Tow Bar Wiring
- Video: Review of Diamond Lights - Load Resistors - DI34ZR
- Shop: Replacement Mirrors
- Shop: Towing Mirrors
- Shop: RV Interior Lighting
- Shop: Suspension Enhancement
- Video: Optronics Load Resistor for LED Lights Installation