Replacement Operator Mechanism and Lift Arm For 7000K MaxxFan Deluxe Roof Vent

Question

Question:

Sirs - I have a MaxxFan 7000K, SN: 2012-02-7000K-0128 where the worm gear in the operator lift mechanism is broken / stripped ... Ive checked your parts list and it appears that the MA10-20281K-1AF Operator Mechanism, Automatic Liftinch and the 10-20222KS, Lifter Arminch are separate pieces however, on my unit, the two parts are integral and do not separate that is until I broke it apart ... my question ... can I use both the individual Operator Mechanism AND the separate Lifter Arm as a bolt-in replacement for my combination mechanism/arm unit ? thanks in advance for your assistance

asked by: Mike K

0

Expert Reply:

Yes, you can use both the operator mechanism part # MA10-20281K-1AF and the lift arm part # MA10-20222KS to replace the broken parts in the MaxxFan 7000K part # MA00-07000K as confirmed by MaxxFan.

expert reply by: Heather A

0

Answer 1

I sure can Kenneth. I checked with Grand Design and the Camco RV Vinyl Trim Insert item #CAM25312-10 is the same size and color as the trim that came on your Imagine 18RBE XLS trailer. It'll slide securely into the tracks and replace the roof…

view full answer...

Answer 2

Hi Denny, To replace your Lift operator you'll need to first manually open your MaxxFan #MA00-04500K using the lift knob. Then you'll need to get up on the roof. Once up on the roof you can press in on the lift arms #MA10-20222KS just enough…

view full answer...

Answer 3

The two most likely causes of a MaxxAir vent fan lid not opening or closing are either going to be a lift motor or operator failure. I recommend removing the motor and applying power directly to this to see if the shaft turns. If not, you know the…

view full answer...

Answer 4

When installing the #MA10-20281K-1AF replacement operator, you might need to 'clock' the mechanism slightly which could take a little bit of trial and error, but the replacement operator does include installation instructions. I've…

view full answer...

Answer 5

Welcome back Rich and thanks for the information! To replace your Sharp Carousel microwave R-820BK-F, I recommend the Greystone Built-In RV Convection Microwave item #GR27FR. It measures 21" wide x 11" tall x 15-3/4" deep.…

view full answer...

Answer 6

Hey Tim, I checked your order notes and back in 2024 you ordered the Maxxair Roof Vent Manual Lift Operator part #MA10-20281K-3CF. Did yours fail again?

view full answer...

Answer 7

We have a large selection of trailer wiring harnesses that are confirmed to fit your 2013 Toyota Tacoma. The correct harness will depend on whether or not your truck has a factory 7-way connector. If your Tacoma came with a factory 7-Way installed, I…

view full answer...

Answer 8

We do have the exact parts you need and yes you can order it through us! I verified with the manufacturer for you that the correct parts for your MaxxAir 4801K are the following: - Replacement Operator Mechanism #MA10-20281K-1AF - Replacement Lift…

view full answer...

Answer 9

Hey Adam! Yes, the Trailer Hub and Drum Assembly #TRU66AV will work as a replacement on your axle. This fits the standard #84 spindle found on 3,500 lb axles and has a 5 on 4-1/2 bolt pattern. Then for replacement brakes you can use the etrailer…

view full answer...

Answer 10

Hey Donnie, thanks for reaching out. We do not carry the Alpha Systems beige roof membrane in an exact 30' x 8-1/2' size, but we do have the Alpha Systems SuperFlex Roof Membrane #AL39UV, which measures 30' x 9-1/2'. That is the…

view full answer...

Answer 11

Hey Dirk, the correct torque spec for 3,500 lb axle u-bolts is 45 and 70 ft lbs. Are you replacing leaf springs?

view full answer...

Replacement Operator Mechanism and Lift Arm For 7000K MaxxFan Deluxe Roof Vent

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching