RV Sewer Hose That Fits Thetford Elbow 01665

Question

Question:

I need a replacement sewer hose with 3inch inside diameter to fit a Thetford elbow part # 01665.

asked by: Larry

0

Expert Reply:

I recommend Quick Drain RV Sewer Hose part # D04-0121 that measures 20 feet long. You need the Valterra 3" Thetford Bayonet to 3" Standard Bayonet adapter part # T05-2285VP to fit into the Thetford elbow.

expert reply by: Heather A

0

Answer 1

You are looking for the Valterra Valve Fitting Adapter - 3" Thetford Bayonet to 3" Standard Bayonet - White item #T05-2285VP.

view full answer...

Answer 2

The lugs of a sewer pipe fitting can not be fixed so you would have to completely replace the fitting. To do that you'll have to first empty out the tank, which since your lug fitting has broken off will require you to hold the hose in place to…

view full answer...

Answer 3

Hi Sherry; the Replacement Seal for Valterra 3" Caps and Hose Adapters #T201 you were looking at is the correct seal for your #T05-2285VP.

view full answer...

Answer 4

The specific fittings and valves you need will ultimately depend on the kind of grey water tank that you plan on adding to your enclosed trailer. If there are threaded fittings or specific diameter openings on your tank, you will need to find the…

view full answer...

Answer 5

Based on your picture the fitting appears to be a bayonet fitting. So for an adapter that fits that fitting and gives you the ability to step down to a few different hose sizes we have the part #F02-3112. Check out the review video I attached for…

view full answer...

Answer 6

All of our hoses and fittings are for the standard fit bayonet which is not what you have. You can either use the adapter #T05-2285VP you referenced to adapt the older thetford fittings to the standard bayonet or if you don't want an additional…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

RV Sewer Hose That Fits Thetford Elbow 01665

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching