How to Test HydraStar HBA-CAM Module with Multimeter
Updated 04/26/2024 | Published 05/16/2019
Products Featured in This Question
Question:
I would like to test a HBA-CAM 381-7073 and a HBA-CAM 381-7063. We have used both of these modules on our trailers and I need to know how to test them to see if theyre still good. Is there a way to test one that is installed or uninstalled? Thanks
asked by: Arnold G
Helpful Expert Reply:
Essentially the adapter part # HBA-CAM is designed to simulate amperage draw of a brake magnet by use of resistance. So you can use an multimeter like # PTW1714 set to read amperage to probe each wire of the adapter. As long as you are seeing over 7.5 amps the adapter would should allow a brake controller to think a trailer is connected.
Product Page this Question was Asked From
Hydrastar Electric Over Hydraulic Actuator Adapter Module for Ford and Chevy Brake Controllers
- Accessories and Parts
- Brake Actuator
- Disc Brakes
- Hydraulic Drum Brakes
- Adapters
- Hydrastar
more information >
Continue Researching
- Shop: Hydrastar Electric Over Hydraulic Actuator Adapter Module for Ford and Chevy Brake Controllers
- Shop: Brake Controller
- Article: Trailer Brakes Not Working? Troubleshooting Guide
- Shop: Hydrastar Electric Over Hydraulic Actuator for Disc Brakes - 1,600 psi
- Shop: Curt TriFlex NEXT Trailer Brake Controller w/ Plug-In Harness - 1 to 4 Axles - Proportional
- Shop: Hydrastar Marine Electric Over Hydraulic Actuator for Disc Brakes - 1,600 psi
- Shop: Hydrastar Vented Marine Electric Over Hydraulic Actuator for Drum Brakes - OEM - 1,000 psi
- Shop: Deutsche Hydrapro CAM Adapter Module for Dexter and Hydrastar Electric Over Hydraulic Actuators
- Shop: Adapter Module for BrakeRite Electric Over Hydraulic Actuator - OE Ford, GM Brake Controllers
- Q&A: Should Brake Output Pin of 7-Way Have Voltage When Brakes are Applied without Trailer
- Video: What to Know About the Curt TriFlex NEXT Trailer Brake Controller
- Q&A: How To Install HBA-CAM Hydrastar Adapter
- Search Results: brake controller
- Video: Hydrastar Brake Actuator HBA-CAM Review
- Q&A: Troubleshooting Integrated Brake Controller Not Working with HBA-CAM
- Video: In-Depth Review of the Trailer Coupler
- Video: Redarc Tow-Pro Liberty Brake Controller Review RED24FR
- Q&A: Trailer Brakes Do Not Activate With Brake Pedal When Trailer is Sitting Still
- Q&A: How to Test Brake Controller without Trailer Connected
- Q&A: Is the HydraStar # HBA-CAM Adapter Compatible with a HydraStar with Serial Number 310837
- Article: Trailer Wiring Diagrams
- Q&A: Is a Hydrastar Electric Over Hydraulic Actuator Adapter Module Needed on a 2021 GMC Sierra 3500HD
- Video: All About the etrailer Adjustable Channel Mount Cast Trailer Coupler
- Video: Checking Out the Cast Trailer Coupler
- Video: Let’s Check Out the Dexter Bolt-On Coupler for 2 5/16" Ball
- Search Results: hydrastar brake actuator
- Search Results: tuson rv brakes trailer brake controller
- Search Results: hydrastar cam
- Search Results: brake disconnect
- Shop: Vehicle Tow Bar Wiring
Coley
4/26/2024
I have the 381-7063 in my trailer. My truck is a 2020 F550. My brake controler is working. My brakes on the DRV trailer, brake controller and +, - work too. I'm not getting an error in the Ford dash of being disconnected. What is not working is the F550 does not turn on battery charge power to the DRV rv trailer. I have connected my truck F550 to a newer work trailer and the Brake Module did send power. Volts on battery in trailer confirmed it was charging. Ford states the truck must detect the trailer, and brake must be depressed before battery charger is sent to trailer. If my F550 can see my DRV rv trailer and my dash indicates the trailer is connected, does that indicate the 381-7063 is working? Does the 381-7063 play a part in the battery charge function??