Height of Horizontal E-Track Part # E19148

Question

Question:

What is the height dimension of the Horizontal E-Track, # E19148. Rather than surface mounting the track, I am considering routing out a channel so I still have a flat deck in my trailer, but not if it requires cutting too deep into the floor.

asked by: Ken

0

Expert Reply:

Routing out a channel in the trailer like you describe is a very slick method of attaching the e-track that works very well.

The e-track is .430 or a bit less than 7/16 of an inch thick (see photo).

expert reply by: Mike L

0

click to enlarge

Answer 1

The E-Track Wood Beam Socket you mention, part #59149 can be mounted in any orientation you wish.As you can see in the photo I provided, the slots in the E-Track measure 2 inches apart on center. Moving from one slot to the next would provide 2…

view full answer...

Answer 2

The capacity is 2,000 lbs per track for the etrailer Horizontal E-Track - Black Powder Coated Steel - 2,000 lbs - 94" Long #e42VR. The weight capacity is per track, so using two of them side-by-side will give you a 4,000 lb capacity. So yes it…

view full answer...

Answer 3

The E-Track has slots that have a length of 2.45-inches and a width of .58 inches. See attached diagram.

view full answer...

Answer 4

The roller of the Erickson Roller Idler for E-Track #EM09144 that you referenced is 3 inches from where it attaches to the E-track. The E-track will then be 7/16 of an inch from the ground so in total the roller of the #EM09144 is 3-7/16 inches tall…

view full answer...

Answer 5

The Brophy 5 Slot Tool Rack for E-Track - Black Powder Coated Steel #ETTH is 24 inches long edge to edge. The inner diameter of each slot is 2 inches and the fittings that mount to your E-Track are 16 inches on center. I've attached a couple…

view full answer...

Answer 6

I went out into our warehouse and measured the distance from the ratchet mechanism to the e-track fastener of the Snap-Loc E-Track Tie-Down Strap #SLLS28RER and found that it measures 7-1/2 inches.

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Hey Jerry, GM moved the placement of their puck systems starting with 2020 models so you are correct that the pucks would have the hitch not sit directly over the axle. GM did the math and made sure that this placement wouldn't adversely affect…

view full answer...

Answer 10

Hey Tom, congrats on the new truck! Typically when we hear that someone has the OEM tow prep package they mean the puck system. This is going to be five circular holes built into the bed of your Ram truck and is by far the best way to attach a 5th…

view full answer...

Answer 11

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 12

Since we don't carry the PullRite line I can't really speak to their quality but from what I can see from there website their 2900 model is fairly similar to the Demco Autoslide 5th Wheel Hitch w/ Slider #DM89GV. Both hitches offer 14"…

view full answer...

Height of Horizontal E-Track Part # E19148

Product Page this Question was Asked From

Continue Researching