How To Remove Broken Wheel Stud on the Dexter Trailer Hub & Drum Assembly # 8-174-5UC3
Updated 07/14/2020 | Published 01/04/2012
Products Featured in This Question
Question:
Dexter 5 spoke hud 12x2.....broke the stud, does it screw out or beat it wit a hammer
asked by: Mike
0
Expert Reply:
On the Dexter Trailer Hub & Drum Assembly, part # 8-174-5UC3, the wheel studs are a screw-in stud. The wheel stud would be the Trailer Hub Wheel Stud, part # 25-11. This is a 9/16 inch stud that has a total length of 3 inches.
expert reply by:
Jeff D
0
Product Page this Question was Asked From
Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility
- Trailer Hubs and Drums
- Hub with Drum
- Standard
- 25580 / 15123
- Standard Grade
- For 6000 lbs Axles
- For 7000 lbs Axles
- 9/16 Inch Stud
- 5 Spoke Utility
- Dexter
more information >
Continue Researching
- Search Results: a~frame jacks trailer jack
- Search Results: trailer tongue jacks
- Search Results: trailer tires and wheels
- Search Results: dometic water heater door
- Search Results: rv steps
- Search Results: porch with handrail rv steps
- Search Results: a frame tongue jack
- Q&A: Replacement Hub for Trailer with 84 Spindle Dimensions
- Shop: Lippert Manual Pull-Out Step for RVs - Triple - 7" Drop - 25-3/4" Wide - Steel - 300 lbs
- Shop: Dexter Trailer Hub and Drum Assembly for 3,500-lb Axles - 10" Diameter - 5 on 4-1/2
- Video: Feature Review Trailer Hub and Drum Assembly
- Shop: Round A-Frame Trailer Jack - Sidewind - 15-5/8" Travel - 5,000 lbs
- Shop: Kenda Karrier KR53 ST205/75R15 Radial Trailer Tire with 15" Black Mod Wheel - 5 on 4-1/2
- Video: Detailed Breakdown of the Dexter Trailer Hub and Drum Assembly for 3,500-lb Axles
- Video: Complete Breakdown of the Dexter Trailer Hub and Drum for 3,500-lb Axles
- Shop: Excel RV Tankless Water Heater - Gas - Electric Ignition - Vent Free - 38,000 Btu
- Shop: Kenda Karrier KR53 ST205/75R15 Radial Trailer Tire with 15" Silver Mod Wheel - 5 on 4-3/4
- Video: etrailer VS Dexter Self Adjusting Brakes Comparison
- Shop: Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 4-1/2 - Galvanized
- Q&A: Should I Replace the U-bolts When Replacing the Leaf Springs
- Q&A: Are etrailer Branded Trailer Brakes Good?
- Q&A: Is Additional Grease Needed to be Pumped into Dexter Trailer Hub that is Pre-Greased
- Q&A: Instructions to Wire a Trailer for Electric Brakes
- Q&A: Comparing Road Armor, E-Z Flex, Equa-Flex, and MORryde Cushioned Equalizers for Tandem Axle Trailer
- Q&A: How do etrailer Brand Trailer Brake Assemblies Compare to Lippert and Dexter
- Video: Dexter Nev-R-Adjust Electric Trailer Brakes Review
- Video: Let’s Check Out the Timken Replacement Trailer Wheel Bearing-TMK49FR
- Video: A Closer Look at the Dexter Trailer Axle Beam with 4" Drop E-Z Lube Spindles
James C.
7/9/2020
I have a old trailer w/srew in bolts to hold wheel on & I need to put on new tires & in trying to take off wheels & three bolts have broke off in hub (so far). I need to know how to get bolts out of brake drum ? Any help would be a life saver !?! Thanks for your help & time ! ! James