Replacement Vinyl Window Trim Insert for Trailers and RVs

Question

Question:

I need to replace my vinyl window trim. Mine has a groove on each edge to fit around the frame. I cant see that on your trim? What trim should I get?

asked by: James S

0

Expert Reply:

The Camco RV Vinyl Trim Insert - White - 100' Long x 1" Wide # CAM25202 is designed to fit all the standard trim rails. The rails normally have the lip on either side that the vinyl tucks under. I've attached a photo of this trim to assist. This trim comes in different colors and different widths. I've linked the page to all your options to assist.

We don't have anything that fits around the frame.

expert reply by: Jason S

0

click to enlarge

Answer 1

Yes, the Camco Trim Vinyl part #CAM25202 that you referenced is the correct replacement trim piece you'd need for your camper.

view full answer...

Answer 2

All of the vinyl trim we currently carry is either 1 inch wide like #CAM25202 or 3/4 inches wide like #CAM25262. There is not a 2 or 3 inch wide option available. This trim fits inside the metal edging on an RV or Camper Shell. I've linked the…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Replacement Vinyl Window Trim Insert for Trailers and RVs

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching