Distance Between Mounting Holes of Valterra Universal Barbed Drain Valve # A01-2025VP

Question

Question:

What is the center to center measurement of the screw holes please? Thanks

asked by: Barry B

1

Helpful Expert Reply:

I spoke with my contact at Valterra and the distance between the mounting holes of the Valterra Universal Barbed Drain Valve # A01-2025VP is 1.45 inches. This is the same for the black version part # 37204-62415.

expert reply by: Jameson C

1

click to enlarge

Answer 1

Hello Todd. The Base of the Fulton Single Speed Trailer Winch #F59CR is 5-3/8" long and 3-9/16" wide. The total height of the unit is 6-1/8" tall. I threw together a few diagrams to help illustrate. Hope this helps!

view full answer...

Answer 2

I went out to our warehouse to take some measurements of the mounting base on the Fulton Single Speed Trailer Winch #F142306. The plate itself measures 6 inches long and 4 inches wide. The mounting pattern features a few oblong holes that allows it…

view full answer...

Answer 3

You will want to visit your local hardware store as the blinds used in RV campers are typically the same as the blinds used in homes. They can also cut or special order the blinds for your application. The Blind #LC786037 you found is for Lippert…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

Hey Kelvin, welcome back. To flat tow a 2026 Ford Maverick with your Demco Commander II Tow Bar item #DM9511012, I recommend the following parts: Baseplate Kit - Demco Tabless Base Plate Kit item #DM38CV Wiring Harness - Roadmaster Diode 7-Wire to…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Distance Between Mounting Holes of Valterra Universal Barbed Drain Valve # A01-2025VP

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching