Replacement Front Cover for Solera Power Awning Idler Head in Black

Question

Question:

I just need the front cover what part number is that

asked by: Adrian

0

Expert Reply:

The Solera Awning Idler head in black part # LC672052 replacement cover is part # LC289566. This replacement cover is a universal cover for all Solera Plain power and Manual Idler head assemblies. If your idler head has a speaker you need replacement Solera Awning Drive Head Front cover part # LC731463 in black.

expert reply by: Heather A

0

Answer 1

There wouldn't be anything else that you could check on the Lippert Electric Trailer Jack with Footplate #LC285318 since the only issue you'd probably have would be internally with either the threaded rod or gears. Most likely you'll be…

view full answer...

Answer 2

The screw size for the attachment screw on a Solera Power Awning Idler Head #LC672052, is a 5/16"-18 x 2-1/4" Phillips head screw. You can pick this up at your local hardware store.

view full answer...

Answer 3

Hello Mandy, thanks for writing in. On the Solera powered awning they have to main style covers. One of them is the Regal Style and the other is the Plain style. In order to determine which one you have you will want to look and see if it has the…

view full answer...

Answer 4

Hello Anthony. We definitely have a replacement vent option for you, but 2000 TS is not actually a model number or part number, so I do not have a way to look that up. Nonetheless, if you are looking for a replacement, I recommend the MaxxFan Deluxe…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Replacement Front Cover for Solera Power Awning Idler Head in Black

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching