Can MaxxFan Roof Vent be Wired to Wall Switch

Question

Question:

I am interested in replacing a bathroom exhaust fan with the model 6401k. I have an existing wall rocker switch that turns the existing fan on/off. Will I be able to set the speed on the fan, and use the wall switch to turn it off/on? I see answers that seem to contradict each other with other model numbers:

asked by: Randy R

0

Expert Reply:

I spoke with my contact at MaxxAir regarding the MaxxFan Deluxe Roof Vent # MA00-06401K. He said that while it technically can be done, they do not recommend wiring any of their fans to a separate switch. The reason for this is that their fans are designed to have a constant 12V feed, and when an external switch is used there will be a short spike in voltage every time the switch is turned on. Over time this higher voltage input can start to cause issues with the circuit board on the vent.

If you do decide to do this though then you would indeed be able to turn the fan on and off from the wall rocker switch and control the speed settings by using the panel on the unit itself. Keep in mind though that with this setup the fan speed would reset everytime you turn it off which would require you to bump it up to your desired speed every time it's turned back on.

expert reply by: Chris R

0

Answer 1

The MaxxFan Deluxe Roof Vent w/ 12V Fan #MA00-06401K only draws 5 amps so you don't need to go crazy with the wiring gauge but I would still recommend 10 gauge like part #10-1-1 (sold by foot) as it's heavier than you'd ever need and will…

view full answer...

Answer 2

Hey Doug, yes the EZ Lube Grease Caps with 1.99" OD #DX69HR that you referenced do fit the 3,500 lb axle Lippert hubs that you have. Did you lose your current caps?

view full answer...

Answer 3

For a white motion detector light I recommend the Solar Powered LED Porch Light for RVs #DG0168. This light has both motion detection sensor mode and dusk to dawn sensor mode to provide lighting, safety, and security. It is solar powered so you…

view full answer...

Answer 4

For a Lippert 4,400 lb trailer axle the correct bearing kit is the part #BK2-100 which includes inner bearing #L68149, inner race #L68111, outer bearing #L44649, outer race #L44610, grease seal #58846, a cotter pin and a tang washer.

view full answer...

Answer 5

We've actually had this one asked before and have consulted with MaxxAir. Even though you can technically install the MaxxFan Deluxe Roof Vent #MA00-06401K wired to a separate switch, it is not recommended. The reason for this is that their fans…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Thanks for the picture! I checked with Progressive Dynamics the replacement power converter you need for your Parallax Series 7300 Model 7345 is the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 45 Amp item #PD4645V.

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Can MaxxFan Roof Vent be Wired to Wall Switch

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching