CE Smith Bolster and Swivel Bracket Assembly that Fits 1988 Landau Trailer

Question

Question:

I’m replacing the bunks and bolster/swivel brackets on an old 1988 Landau Trailer that holds an Alumacraft 16.5 Aluminum Bass Boat with 50HP Yam. The current bolster brackets measure 9-inches and there are 6 of them. I assume I can use the Item#CE10000G for replacement.

asked by: Tim

1

Helpful Expert Reply:

Yes, based on the picture you sent in the CE Smith Bolster and Swivel Bracket Assembly # CE10000G that you referenced will fit and work well on your 1988 Landau Trailer.

expert reply by: Jameson C

1

click to enlarge

Answer 1

Hey Peter, what hanger dimensions do you need? What height from the mounting surface does the bolt hole need to be? With that I can see if we have a thicker gauge steel hanger option.

view full answer...

Answer 2

Hey Mark, thanks for reaching out, and congrats on the new camper! We have just the thing! Here is what I recommend: - Blue Ox SwayPro Weight Distribution w/ Sway Control for 2-1/2" Hitch - 15K GTW, 1.5K TW #BLU54TR The Blue Ox WD hitches are…

view full answer...

Answer 3

I do have some parts for you but we aren't custom trailer builders and adding electric to a trailer is not a simple task. What I can tell you is that most interior lights are 12 volt so if you want outlets, lights, and shore power you'd need…

view full answer...

Answer 4

If you're only wanting to setup AC service in your enclosed trailer then you could choose pretty much any 30 or 50 amp power inlet you wanted and then just run the appropriate gauge wire between the inlet and your panel. You can definitely…

view full answer...

Answer 5

You need to use the inner diameter of your hub bore to determine what size Bearing Buddy you need. If you measured the outside diameter and chose your Bearing Buddy on that, then it will not fit. If you measured the inner diameter, then as you said,…

view full answer...

Answer 6

The portion you need to measure is not the cap, but the the hub bore. Remove the grease caps and measure the diameter of the opening the caps occupy. This is the hub bore. You will need an accurate measuring devices like a set of dial calipers that…

view full answer...

Answer 7

Hey Steve, it looks like you are comparing the Malone EcoLight Sport Trailer with J-Carriers part #MAL93FR with the Yakima LowRider Kayak Trailer #Y82QD. The Malone actually has a 400 lb weight capacity vs. the Yakima which is rated for 750. The…

view full answer...

Answer 8

The bearing part #L44649 has an inner diameter of 1.063 and is typically used in 3,500 lb axle hubs and the #L44643 has an inner diameter of 1 inch and is typically used on 2,000 lb axle hubs. If you can get me more info on your trailer like axle…

view full answer...

Answer 9

The model 1980 Bearing Buddy simply means that they fit a 1.980 inch hub bore. There is one difference of note between Bearing Buddy Bearing Protectors #BB1980A (Chrome Plated) or #BB1980A-SS (Stainless Steel) and the Bearing Buddy Bearing Protectors…

view full answer...

Answer 10

Even if the boards can bear the weight of the boat, by concentrating the weight on a smaller, 3 inch surface, there is a greater risk to denting or deforming the hull of your boat compared to having the boat's weight spread out over a larger…

view full answer...

Answer 11

For heavy duty brackets you can use the CE Smith Double U-Bolt Bolster and Swivel Bracket Assemblies #CE10196G-4. These brackets have an extra-sturdy connection since each one attaches with 2 U-bolts. These have an overall height of 16-1/4" and…

view full answer...

CE Smith Bolster and Swivel Bracket Assembly that Fits 1988 Landau Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching