Width of CE Smith U-Bolt # CE15503A

Question

Question:

Is the 3 1/8 inch width of this U bolt the inside dimension ? My boat trailer is made of 3 X 3 inch steal. I need this U bolt to hold a 5 inch spool roll with bracket that you sell. Thank you

asked by: Alan

0

Expert Reply:

The 3-1/8 inch dimension on the CE Smith U-Bolt # CE15503A that you referenced is indeed taken from inside to inside on the posts. I have attached an image to assist. It will work great for your 3 x 3 inch trailer frame.

expert reply by: Chris R

0

click to enlarge

Answer 1

Hey Ken! As far as we know there is not a good way to do this. I suppose you could attempt to run some additional lines, add in tees, and add in some kind of valves, but I don't think it would work well (or at all). Also, if a valve failed, you…

view full answer...

Answer 2

In order to convert the hydraulic disc brakes on your trailer to electric, you will need a electric over hydraulic (EOH) actuator and a breakaway kit. The HydraStar Vented Marine Electric Over Hydraulic Actuator for Disc Brakes part #HS381-8067 is an…

view full answer...

Answer 3

Hey David, so what you can do is lock out the moving components of your actuator by having them welded together or having a bolt ran through both pieces to hold them together. Or you could have the whole thing removed and install a straight tongue…

view full answer...

Answer 4

The HydraStar Marine Electric Over Hydraulic Actuator w/ Breakaway and 7-Way RV Harness item #HS381-9067 is designed to work with an aftermarket electric over hydraulic brake controller. The HydraStar Vented Marine Electric Over Hydraulic Actuator…

view full answer...

Answer 5

Hello Jeff, Since you swapped out your hydraulic brakes for electric brakes you will no longer need a surge brake actuator since you will be controlling the brakes with a brake controller. To replace your Atwood 61101, I would go with the Buyers…

view full answer...

Answer 6

I was able to go out to the warehouse and measure the clamp-on mounting bracket for HydraStar EOH Actuators #HS304-7169. I made you a dimensional diagram to better see, but found that the mounting holes for the u-bolt are 13-1/8 inches by 3-5/8…

view full answer...

Answer 7

I took the measurements of the Multipurpose U-bolt, part #CE15504A, which you can see on the enclosed diagram. You'll note that the length of the U-bolt is 3 inches, which may be too short for your application. The closest sized U-bolt we are…

view full answer...

Answer 8

The vertical bunk brackets do not have a weight capacity rating. You should be fine with the aluminum, but if you are concerned about the strength then you can stick to the galvanized steel the manufacturer used. - Replacement CE Smith Vertical Bunk…

view full answer...

Answer 9

If you're going to go with stainless U-bolts, go with the 316 stainless if you're using the trailer in a saltwater environment, the extra molybdenum in the 316 will do a better job of resisting corrosion. The CE Smith #CE15503A is the longest…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Width of CE Smith U-Bolt # CE15503A

Product Page this Question was Asked From

Continue Researching