What Type of Wheel Would Need to Be Used with Trailer Hub # AKHD-550-35-K

Question

Question:

What model or type of wheel I need for a Hub AKHD-550-35-K?

asked by: Juan A

0

Expert Reply:

The etrailer.com hub part # AKHD-550-35-K that you referenced has a 5 on 5 inch bolt pattern so for a wheel with that matching bolt pattern you'd want the part # AM20538DX and you'd be set. This is a 15 inch diameter wheel that is 6 inches wide. I attached a review video for this wheel for more info for you to check out as well.

expert reply by: Jameson C

0

Answer 1

The Lippert Electric Trailer Brake Kit #LC66WD mounts to a brake flange 2-7/8" on center vertically and horizontally.

view full answer...

Answer 2

Picking out brake assemblies for trailer axles is actually pretty easy but I am not able to determine the info I need from your trailer info since it's not something manufacturers keep records of. You do need to order a total quantity of 4…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

I sure can Bob and thanks for the information! Since you have a Lippert 3,500 lbs axle you'll be able to use the Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles item #AKHD-545-35-EZ-K, you were looking at. These have a 5 on 4-1/2 lug nut…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 12

Hey Robert, yes the Kodiak disc brake calipers part #KDBC225DAC that you referenced will replace the Tie Down calipers you have now 46304, they can be used as a left or right hand caliper and does come with ceramic brake pads. If you ever needed…

view full answer...

What Type of Wheel Would Need to Be Used with Trailer Hub # AKHD-550-35-K

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching