Timbrens Suspension Enhancement Recommendation for Trailer with 7,000 lb Axles

Question

Question:

I have two sets of Timbrens that were used on my 2013 F350 Dually. I have replaced them with Air Bags. Can the Timbrens be install on my 5th Wheel 7,000lb axles to help with suspension and increase load capacity? Would different hardware be needed? Axles and 5th Wheel frame is made by Lippert. See attached picture of axle. Thanks,

asked by: Don S

0

Expert Reply:

Timbren makes a 7,000 lb capacity kit designed specifically for trailer axles like yours as part # TTRA1032 but we do not have a way for you to adapt your truck's Timbrens to your trailer.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Going from standard leaf springs - even with a rubber equalizer - to a whole new suspension system will 100 percent upgrade the ride of your 2021 Grand Design Reflection 303RLS. While you will certainly get some benefit by going to the Comfort Ride…

view full answer...

Answer 2

The Timbren Trailer Suspension Enhancement System, part #TTRA1032, can be installed on trailers with I-beam frames. This system provides additional support so you have a comfortable ride. The springs become more rigid as additional weight is added.…

view full answer...

Answer 3

MORryde does have a suspension upgrade kit that I highly recommend. It comes with 1/2" thick shackles, along with wet bolts and bronze bushings. You will want to choose a kit based on the length of your current shackles. For 2-1/4" you need…

view full answer...

Answer 4

Sounds like you are trying to figure out the weight capacity for your 3 axle trailer. It is nearly impossible to determine leaf spring capacity based on dimensions. But you can determine axle capacity by measuring. Since your axles are 3 inches in…

view full answer...

Answer 5

The varying heights of the hangers is all designed so that you end up with the leaf springs as level as possible and still end up a desired distance away from the trailer frame. It may seem odd, but the center hanger will stick down further because…

view full answer...

Answer 6

Send me the pictures you have and I'll see if it's something we can get.

view full answer...

Answer 7

Hello Eric, thanks for reaching out. We do carry replacement surge brake actuators, and even some replacement parts for certain models. I do not have a way to know exactly what actuator is currently on your trailer though. If you are looking for…

view full answer...

Answer 8

When replacing shackle straps they should be the same length as the ones that were previously on your tandem axle trailer (if possible); replacing them with longer straps will result in additional play in your trailer suspension which could lead to…

view full answer...

Answer 9

Ff the springs you are installing are 25-1/4 inches, you would need to place the hangers between 24-3/4 and 25 inches apart. The shackle should be angled as the drawing shows in the attached helpful article, which should be toward the rear of the…

view full answer...

Answer 10

The correct hanger spacing for your trailer will depend on several factors; I cannot generalize and give you a specific figure. Hanger spacing depends on spring length, the size of the equalizers used and the length of the shackle straps. The linked…

view full answer...

Answer 11

Since your current equalizers are having issues with hitting the trailer frame that would indicate that they are too long currently so going with the shorter #K71-359-00 would be what you'd want instead.

view full answer...

Answer 12

When changing the size of the equalizer that is on a trailer, this will affect the size of hangers needed or the spacing of the hangers. For example, if you were to go with an equalizer that is one inch taller, you could keep the center hanger the…

view full answer...

Timbrens Suspension Enhancement Recommendation for Trailer with 7,000 lb Axles

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching