Will Dexter Disc Brake Actuator Replace Titan Model 6 Actuator?

Question

Question:

I have a titan model 6 can I use this part and put my lockout on it?

asked by: Robert B

0

Expert Reply:

Yes, you can use the Dexter Disc Brake Actuator # T4747220 as a replacement for your current Titan Model 6 actuator.

expert reply by: Kyle S

0

Answer 1

Dexter does not have an option for an electric lockout on their drum brake actuators, but that doesn't mean you can't add one. It is as simple as adding the Replacement Solenoid Valve for Dexter Brake Actuators #T4748800 to the #T4500600.…

view full answer...

Answer 2

The Titan Surge Trailer Actuator part #T4747220 will pretty easily install in place of what you have now but looking at the picture of what you have and what looks like an equal distance between the mounting holes it would seem most likely that you…

view full answer...

Answer 3

The Replacement Solenoid Valve #T4748800 was specifically designed to be used on your Titan Model 6 coupler so I can guarantee it will work for you. We have had several customers do exactly what you are looking to do without any issue.

view full answer...

Answer 4

If it's a slip-on rotor setup what you'll want is the Kodiak Disc Brake Kit part #K2R526S for each axle. This gives you a stainless steel rotor and caliper. We do not have any stainless rotors that will fit with the UFP calipers you have now.…

view full answer...

Answer 5

The bolt hole dimensions of the Demco Brake Actuator #DM8669112 are 12-1/2 inches on center and 3 inches on center. I've attached a photo to assist. The Titan #T4747220 has mounting holes that are 3 inch on center so 2 of the 3 holes will align…

view full answer...

Answer 6

When bleeding the brakes on a surge actuator, such as the Dexter DX7.5L A-60 Brake Actuator w Electric Lockout #DX56FR, you want to start by making sure there is fresh fluid in the reservoir then press a screw driver against the rod in the access…

view full answer...

Answer 7

Yes, the Demco Hydraulic Brake Actuator w/ Drop and Electric Lockout #DM8750311 will easily handle 4 brake assemblies like what a tandem axle trailer has.

view full answer...

Answer 8

We can get both of your axles set up with disc brakes, and for 3,500 lb axles, since you are converting to disc brakes you'll need a hub-and-rotor disc brake assembly. For the correct kit, as well as the disc brake actuator and brake lines, here…

view full answer...

Answer 9

Yes, the Titan Premier Disc Brake Kit #T2HRCM10DAC will work as a starting point to upgrade your existing drum brakes to Disc on your 1995 Caulkins Boat Trailer. This Kit is Dacromet-plated to help resist corrosion and includes the hub/rotors,…

view full answer...

Answer 10

I went out to the warehouse and measured the bolt holes on actuator #T4747220. The 2 larger holes are spaced 5 inches apart on center. I have included a picture showing this and other measurements for you.

view full answer...

Answer 11

You will need to cut that off of your 2001 Cobalt 240 to replace the actuator since there are no replacements that will fit. I recommend welding on a straight tongue so you can use a bolt-on actuator like the Dexter Zinc-Plated Brake Actuator…

view full answer...

Answer 12

You are correct that disc brakes require an actuator with higher psi pressure than what is required by drum brakes. Drum brakes need pressure of 1000-psi but discs need 1500 to 1600-psi. You can convert your Titan Surge-O-Matic Model 6 actuator to…

view full answer...

Will Dexter Disc Brake Actuator Replace Titan Model 6 Actuator?

Product Page this Question was Asked From

Continue Researching