Thread Size for PlusNut Hardware # Y8880039

Question

Question:

What is the thread pattern for the hole in part Y8810074?

asked by: Austin

0

Expert Reply:

The Replacement PlusNut Hardware Kit, part # Y8880039 you asked about are 10-32 mm with a thread pitch of .75 inch according to our contact at Yakima.

expert reply by: Jameson C

0

Answer 1

Yes, the Replacement PlusNut Hardware Kit #Y8880039 that you referenced is an optional hardware kit for your Yakima 60" Tracks for Roof Racks #Y01135. This hardware kit is designed for use with sheet metal roof applications.

view full answer...

Answer 2

The Yakima PlusNuts replacement part #Y8880039 is the optional hardware kit for Yakima roof rack tracks #Y01126 (42 inch) and #Y01127(54 inch) and are made out of steel. The roof-rack tracks are an anodized aluminum so you wouldn't have any…

view full answer...

Answer 3

You can use either the Yakima 54" tracks #Y01127 or 60" tracks #Y01135 on naked roofs without needing to remove the headliner, and as long as you're careful, you won't damage the headliner during installation. It should be noted…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 9

Welcome back Scott! The Victron MultiPlus Pure Sine Wave Inverter Charger item #VN63VR has a 94% efficiency rating over the Go Power ASW Series Advanced Sine Wave Inverter item #GP44XR. The Victron item #VN63VR is also going to be noticeably quieter…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

Hey Jason, whenever available I would recommend going with the channel attachment for roof rack accessories including the Thule Hullavator part #TH898 as its simpler stronger, and it's basically the future of most roof rack accessories as it…

view full answer...

Answer 12

It sure is Doug and congrats on your new truck! The TruXedo Pro X15 Soft Tonneau Cover item #TX33TV has been confirmed to fit your new 2026 Ford Maverick. The TS Rails item #TH25FR are going to fit alongside the rails of the Pro X15 item #TX33TV on…

view full answer...

Thread Size for PlusNut Hardware # Y8880039

Product Page this Question was Asked From

Continue Researching