Hitch Mount Recommendation that Fits 12k Bulldog Winch # BDW10039

Question

Question:

Just got my Bulldog winch #100039 and receiver mount BDW 20156 great service, thanks. Will the wire extension BDW20298 work for extending power to the rear of my pickup or do you have a better recomendation. I dont plan on a perminate wire installation

asked by: Neil N

0

Expert Reply:

Yes, the Bulldog Winch Mount part # BDW10039 does work with the Bulldog Winch part # BDW20155 that you also referenced. The mount fits winches with up to a 12k capacity and mounting dimensions of 10" by 4-1/2" which is exactly what the winch you mentioned has.

expert reply by: Jameson C

0

Neil N.

1/3/2018

Just got my Bulldog winch #100039 and receiver mount BDW 20156 great service, thanks. Will the wire extension BDW20298 work for extending power to the rear of my pickup or do you have a better recomendation. I dont plan on a perminate wire installation

Jameson C.

1/3/2018

Yes, the Bulldog Winch Booster Cable Set # BDW20298 can be used to power a winch at the rear of a truck as a temporary type solution. This cable set is 20 feet long and is 2 gauge wire which is rated for up to 2,000 amps.

Answer 1

That's a hard figure to give as different winches draw different amounts of amperage and they also draw different amounts of amperage based on how close to the capacity the winch is at. A handful of hours is commonly the amount of time for most…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Hitch Mount Recommendation that Fits 12k Bulldog Winch # BDW10039

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching