Installing Blue Ox Tail Light Wiring Kit with Block Diode on Towed Vehicle
Updated 09/26/2017 | Published 09/25/2017 >
Products Featured in This Question
Question:
Just making sure I’m doing this right so in the rear of the car I cut my wires to my turn signals and brake lights one side goes on diode on front of towed car and the other side going to the light will go on diode for back of towed car. I’m useing the A diagram no amber lights. What a bout running lights do I need to run a wire from both rear lights for both running lights to operate. Thanks
asked by: Kaye
Expert Reply:
You are on the right track! When installing the Blue Ox Trail LIght Wiring Kit # BX8811, you will essentially have wires coming into the block diode from the RV and in from the vehicle. Then the wires coming out will go to the vehicle's rear tail lights.
I have attached the complete installation instructions for the Blue Ox Trail Light Wiring Kit for you to take a look at. This will give you much more detailed installation steps than the diagram you are referring to. As you mentioned, you will simply follow the instructions for "Type A" if your vehicle just has standard red turn signals.
Starting in the engine component of your towed vehicle, you will run the 26 foot harness through the firewall, under the driver side door, under the back set and into the trunk area. Depending on how your motorhome/RV is setup, the wire at the front of the engine compartment should be wired into either a 4-wire or 6-wire trailer plug.
At the rear of the towed vehicle, you are going to first make sure that the white wire is grounded to the vehicle chassis. Using a circuit tester like # PTW2993, you will then need to identify the "hot" wires that power the brake and tail lights/running lights on your car. Once the tail light and turn signal wires are identified, you will simply make the necessary connections as described in the installation manual.
Product Page this Question was Asked From
Blue Ox Block Diode Tail Light Wiring Kit for Towed Vehicles
- Flat Tow Wiring Harness
- Splices into Vehicle Wiring
- Diode Kit
- Universal Fit
- Blue Ox
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Replacement Upper or Lower Slide Assembly for Kwikee 47 Series Electric RV Steps
- Shop: Voyager RV Backup Camera Monitor - 7" Screen - 4 Video Inputs
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Search Results: trailer hitch
- Shop: Cabin Air Filter
- Search Results: rv and camper bike racks
- Video: Mount: Hollywood Racks Destination E Bike Rack for 2 Electric Bikes on a 2020 Chevrolet Equinox
- Shop: Hollywood Racks RV Rider Bike Rack for 2 Electric Bikes - 2" Hitches - Frame Mount
- Article: Tow Bar Wiring Overview
- Search Results: hollywood destination e
- Shop: Hollywood Racks Destination E Bike Rack for 2 Electric Bikes - 2" Hitches - Frame Mount
- Search Results: hitch bike racks
- Shop: PTC Custom Fit Cabin Air Filter - Charcoal
- Q&A: Comparing e-Bike Racks Compatible with Lectric XP 2.0 Step-Thru Bikes
- Video: Assembling the Hollywood Racks RV Rider 2 Electric Bike Rack
- Shop: Vehicle Tow Bar Brake System
- Video: In-Depth Review of the Hollywood Racks RV Rider Bike Rack for 2 Electric Bikes
- Search Results: trailer wiring
- Video: Best 2020 Chevrolet Equinox Trailer Hitch Options
- Video: Detailed Breakdown of the Hollywood Racks Destination E Bike Rack for 2 Electric Bikes
- Shop: Hollywood Racks Destination Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Frame Mount
- Q&A: Troubleshooting the Fuse Blowing on the Demco Stay-IN-Play Duo Braking System
- Video: Setting up the PTC Custom Fit Cabin Air Filter on your 2020 Chevrolet Equinox
- Shop: Vehicle Tow Bar Wiring
- Shop: Base Plate for Tow Bar
- Shop: RV Exterior Lighting
- Q&A: Replacement Step Control Module for 2011 HR Vacationer
- Q&A: Replacement Monitor for Voyager AOM-7694
- Video: Installation: Hollywood Racks RV Rider Bike Rack for 2 Electric Bikes on a 2021 Chevrolet Equinox

