Will the Roadmaster Rollaway Hitch Protector Fit a Dual Hitch Receiver
Updated 09/06/2024 | Published 07/05/2017
Products Featured in This Question
Question:
Will Roadmaster RM-050 fit onto a Roadmaster dual hitch receiver adapter 4inch /rise RM-077-4 without alterations?
asked by: Paul G
1
Helpful Expert Reply:
Yes, I do not see any issues with the compatibility between Roadmaster Rollaway hitch protector # RM-050 and dual hitch receiver # RM-077-4. Take a look at the video for the hitch protector I have linked. You can see how it attaches to a receiver showing how there wouldn't be interference between the 2 parts.
expert reply by:
Michael H
1
Product Page this Question was Asked From
Roadmaster Rollaway Trailer Hitch Protector
- RV Skid Wheels
- Hitch Mount
- Bolt-On
- Roadmaster
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Q&A: Can Multiple RV Heater Pads with Thermostat 277-000163 Be Wired Together
- Shop: Buyers Products 2-Way Die-Cast Zinc Trailer Connector - Trailer Side - Horizontal Pins with Spring
- Search Results: steel rollers
- Video: What to Know About the Ultra-Fab Steel Micro-Roller for Trailers and RVs
- Video: All About the Roadmaster Dual Hitch Receiver Adapter, 2" or 4" Drop/Rise
- Video: The Low-Down on the Roadmaster Rollaway Trailer Hitch Protector
- Video: The Low-Down on the Malone 2" Dual Purpose Hitch Receiver
- Shop: Ultra-Fab Steel Micro-Roller for Trailers and RVs - Weld On - 2" Wide x 2-1/4" Tall
- Shop: Roadmaster Dual Hitch Receiver Adapter, 2" or 10" Drop/Rise
- Shop: Malone 2" Dual Purpose Hitch Receiver
- Shop: Ultra-Fab Steel Roller for RVs with 2" Trailer Hitches
- Shop: Roadmaster Rollaway Trailer Hitch Protector
- Shop: Roadmaster Dual Hitch Receiver Adapter, 2" or 4" Drop/Rise
- Q&A: Recommended Trailer Hitch Receiver For a 2023 Kia Carnival Least Likely to Scrape on Driveway
- Q&A: How to Prevent the Hitch from Scraping on a 2014 Mercedes-Benz Sprinter
- Q&A: Trailer Hitch and Bike Rack Scrape the Ground when Going Up Inclines with 2006 Honda Odyssey
- Q&A: Will The Roadmaster Rollaway Trailer Hitch Protector Work On Roadmaster Spare Tire Carrier?
- Q&A: Recommendation for Preventing Car Trailer From Dragging Up Steep Driveway
- Q&A: Will Roadmaster Skid Wheel # RM-050 Prevent Scraping When Carrying Bike Rack
- Search Results: trailer hitch
- Video: How to Choose a Trailer Brake Controller
- Shop: Trailer Hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer wiring
- Video: Feature Breakdown: Universal Installation Kit for Trailer Brake Controller
- Article: 30-Amp and 50-Amp RV Service: What's the Difference?
- Shop: Trailer Wiring
- Search Results: trailer jack
- Article: Trailer Wiring Diagrams
- Shop: Suspension Enhancement
Explore Expert Info
![Our Expert]()
on RV Skid Wheels
on RV Skid Wheels
Don G.
9/6/2024
Michael, I just received the Roadmaster Rollaway hitch protector and a 4in rise 2in drop hitch and the instructions specifically state say not to install the Rollaway on a hitch extension. It must be installed on the vehicle receiver. While it may fit on the extension I suspect the restriction is in place to prevent torsion stress that would be applied to the vehicle hitch due to the leverage of an extended hitch mount position. This torsion stress would be much less when the Rollaway is installed close to vertical below the vehicle hitch bar. My application was on a Promaster 2023 chassis with a Thor Sequence house body. My drain valves would need a roller to drop down about 8 or 9 inches at the hitch to prevent damage to the valves. Another problem I encountered was the vehicle hitch has gussets welded vertically on the hitch square channel. These prevent the Rollaway from aligning to put the hitch pin in place.