Replacement Jacks For A Lance 815 Truck Bed Camper

Question

Question:

Need to replace the driver side rear manual jack on our Lance 815 truck camper. Not sure what the manuf is, the type of jack etc to purchase

asked by: May

0

Expert Reply:

I do have options available for you however, we only offer universal jacks sold in pairs not single replacement jacks for your Lance 815 truck bed camper.

If the universal jacks are something you would like to consider, I recommend using the Brophy Cable Camper Jacks part # CJ74. The Brophy jack have a maximum weight capacity of 3,000 lbs. and can lift the camper from 17"-67". They stand 76" tall and are a non-permanent removable option.

expert reply by: Conner L

0

Answer 1

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 2

The Lippert 18:1 Venture Actuator Slide-Out Motor #LC132682 is the replacement for your RV-8000-1 motor on your Glufstream Kingsport 301TB. This motor turns slower than the 8532-18HT and using the incorrect motor may damage the components of the…

view full answer...

Answer 3

The cylinders for the latches need to be measured for length to get you the correct replacements. This means removing the lock cylinder which should not be difficult if it is able to be removed as some are and some are not. If you disassemble the…

view full answer...

Answer 4

Realistically it is best to stick with a Dometic replacement thermostat for your Dometic setup. The #DMC79FR is the correct replacement for your 3316410.012. It may be possible to use a universal thermostat like the #CAM09221 you looked at but this…

view full answer...

Answer 5

Hey William, If you have a Torklift tie down setup for your camper you would want to use turnbuckles that have springs built in like the Torklift Basic SpringLoad part #TLS9000 that you referenced on all four corners. What tie downs do you have?

view full answer...

Answer 6

You should not have a problem with the camper sliding out when you are using any of the Brophy Cable Camper Jacks. The jack is very stable because of the tripod base. That stability will make the jack very difficult to tip to the front or the back.…

view full answer...

Answer 7

Hey Cindy, thanks for reaching out. We may have an extension that will work for you. It will help to know exactly how long of an extension you are needing as this will be one of the main deciding factors. Let me know how long you need it to be in the…

view full answer...

Answer 8

Hello Michael, thanks for reaching out. The Brophy Camper Cable Jacks #CJ31 are better suited a truck bed camper that extends out past the bed rails on each side. They can potentially be used for a camper shell that is flush with the side of the…

view full answer...

Answer 9

Hello Brian, thanks for reaching out. With the Brophy Cable Camper Jacks #CJ74, the L-bracket sits about 3" out from the edge of the jack tube. So it doesn't give you a whole lot of extra clearance. It will only work on setups where you have…

view full answer...

Answer 10

The lift brackets of the Brophy Tripod Camper jacks part #CJ41 extend out from the upright mast the same distance as the feet of the tripods. So as long as the camper extends out past the tires like you said yours did this would work although…

view full answer...

Answer 11

In order to choose the correct high-low adapter to flat tow your Fiat, you will need to take some measurements. With your RV and Fiat on level ground, measure from the ground to the center of your hitch receiver. Then measure from the ground to the…

view full answer...

Replacement Jacks For A Lance 815 Truck Bed Camper

Product Page this Question was Asked From

Continue Researching