Is Kodiak Rotor part # KR10S Sold Individually

Question

Question:

Its unclear to me if item# KR10S is for one rotor or for a set of two rotors. Please clarify. Also, same question applies to item# KR10D Thanks,

asked by: Mike

0

Expert Reply:

The part # KR10S is for a single stainless steel rotor. If you needed a pair you would have to order a quantity of 2.

The same applies to the part # KR10D except this is a Dacromet coated rotor. Dacromet is corrosion resistant, but no steel is more corrosion resistant than stainless steel.

expert reply by: Jameson C

0

Answer 1

Yes, replacement parts are available for Kodiak disc brake kit #K2R35D. For calipers you can use #KDBC225DAC for dacromet or #KDBC225S for stainless steel. Both come in quantities of 1 and are for 3,500 to 6,000 pound axle Kodiak disc brake kits. For…

view full answer...

Answer 2

We do have a few options for your Kodiak 225 calipers #KDBC225S, we offer the Kodiak 10" Rotor #KR10D which have a 5 on 4 1/2 bolt pattern, will fit 14" or larger wheels, and will work on 3,500 pound axles. Finally we also offer the Kodiak…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

Hey Robert, yes the Kodiak disc brake calipers part #KDBC225DAC that you referenced will replace the Tie Down calipers you have now 46304, they can be used as a left or right hand caliper and does come with ceramic brake pads. If you ever needed…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

I currently have four different self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes. You can choose from the following: -Terran Axle Electric Trailer Brakes #TX97ZJ (3,500 Axles) -etrailer Electric Trailer…

view full answer...

Is Kodiak Rotor part # KR10S Sold Individually

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching