How to Get a Ball Mount with 0 inches of Rise or Drop

Question

Question:

I am looking for a 2x2 ball mount, with 0 rise, in black.

asked by: John

0

Expert Reply:

In order to get a ball mount that has effectively 0 inches of rise or drop you would need to get a Trailer Hitch Ball Mount, part # D-4, like the one you referenced that has a 2 inch drop, and then use a 2 Inch High Rise Ball, part # C40034.

I attached links to FAQ articles on ball mounts and hitch balls below for you to check out also.

expert reply by: Jameson C

0

Answer 1

I definitely understand being a bit overwhelmed by the amount of options in front of you, however I can definitely help with differentiating the trailer hitches for your 2019 Subaru Outback Wagon along with explaining my personal recommendation,…

view full answer...

Answer 2

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 3

Lock nuts alone should have been fine but you could use some Loctite, #LT37614, for extra protection. Make sure to use the blue Loctite and not the red version. The red would make it very, very difficult to remove the nuts. Since you mentioned the…

view full answer...

Answer 4

I reached out to my contact at EcoHitch to see if they have seen this issue before with the EcoHitch #306-X7201 on your Tesla and if they have any suggestions. My contact did say that the Tesla rear bumper has quite a bit of tolerance from the…

view full answer...

Answer 5

I took a look at what we got, and it doesn't appear that we stock any of the older Fulton jack parts, however I do have another suggestion. I know you prefer to use what is already there, however since you're wanting to bolt on a wheel, I…

view full answer...

Answer 6

We had the chance to install the Fastway coupler lock part #FA86-0015-318 on an actuator like your UFP A-60 and found that it fit and worked well. Check out the picture I attached to see the lock installed on the coupler.

view full answer...

Answer 7

To replace the hitch ball you would simply loosen and remove the hitch ball nut and pull the ball out of the ball mount hole. You may need a large wrench to loosen the nut. The Tow Ready 1-7/8 Inch Hitch Ball, part #19260, would be a great fit for…

view full answer...

Answer 8

The Torflex Lift Kit #K71-724-02 is meant specifically for the #11 Torflex axles and attaches directly to the side mounted brackets on your trailer's frame without any additional hardware. This kit works with Torflex Axles with a 4,100-6000 lb…

view full answer...

Answer 9

For use as a wheel chock you would only need to use two of the part #AM3604 to keep the trailer from moving. Securing each of the wheels would not be necessary. I attached a demo video for these for you to check out as well.

view full answer...

Answer 10

For a trailer hitch receiver that is confirmed to fit your 2013 Honda Civic I recommend the Curt Trailer Hitch Receiver - Custom Fit #C11391 which is a Class I, 1-1/4 inch hitch receiver. Since all of the Euro ball mounts fit a Class II hitch…

view full answer...

Answer 11

You can absolutely trust the manufacturer ratings for the ball mounts we have available, regardless of whether or not they feature a solid or hollow shank. Ball mounts and other towing products are typically tested well beyond their actual listed…

view full answer...

Answer 12

Using the fob on the Autowbrake Electric Brake Controller #3430001 will not activate the trailer brake lights. This includes the manual override. The key fob will cause the brakes to pulse, similar to an anti-lock brake system. There have been a few…

view full answer...

How to Get a Ball Mount with 0 inches of Rise or Drop

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching