Recommendation for a Coupler Lock for a Collar-Loc Trailer Coupler

Question

Question:

Will this lock work with a sliding collar-lock coupler? I have a Bulldog 12,500 lb., 2-5/16 coupler.

asked by: Jody

0

Expert Reply:

For a Collar-Lok coupler I recommend a lock designed for then such as # BLTL-23 (2-5/16 inch ball), # BLTL-20-40D (1-7/8 to 2-5/16 inch balls), or # BLTL-22 (2 inch ball).

expert reply by: Michael H

0

Answer 1

We do have a lock that will work for your Bulldog 4BWC-AR coupler, which is the Collar-Lok coupler similar to part #BD028462. What you can use is the following: - EZ Lock Trailer Coupler Lock for 1-7/8", 2", 2-5/16" Bulldog Collar-Lok…

view full answer...

Answer 2

The Blaylock Coupler Lock #BLTL-20 that you referenced is designed to fit the Bulldog Collar Lok style couplers like what you see in the picture I attached. If you are looking for a more universal style lock the Fastway part #FA86-0015-318 is very…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Recommendation for a Coupler Lock for a Collar-Loc Trailer Coupler

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching