Nut / Socket Size Used to Raise and Lower the Ram Scissor Stabilizer Jack # TJSC-24

Question

Question:

What size socket is required to fit the nut end on the worm gear threaded rod? Is it 3/4inch or something different?

asked by: Jason D

0

Expert Reply:

The Ram Jack # TJSC-24 measures 3/4 inches. A 19 mm wrench or socket can also be used.

The recommended manual crank handle for this unit is # TJSC-24-HD this has the proper size socket for use with these jacks.

I have linked the above mentioned products to this page for your convenience.

expert reply by: Jackie C

0

Answer 1

I went out to the warehouse to measure the drive nut on the Scissor Stabilizer Jacks #TJSCHD-24. From wrench flat to wrench flat it is 0.72 inches so just a hair under 3/4 inch and just a hair above 18mm.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

Hey Lori, thanks for reaching out! The TorkLift Tie Downs #TL87DR are a custom-fit kit, so there’s no drilling required on the truck itself. Everything bolts up to existing holes in the frame, which helps keep the install pretty straightforward. As…

view full answer...

Nut / Socket Size Used to Raise and Lower the Ram Scissor Stabilizer Jack # TJSC-24

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching