Can 6 of the CE Smith Bolster Brackets CE10002G-4 be Ordered

Question

Question:

is it possible to get 6 of these?

asked by: Ray R

0

Expert Reply:

You would just need to order a quantity of 6 of the part # CE10002G to get six of the brackets that come with the part # CE10002G-4.

expert reply by: Jameson C

0

Answer 1

Your best option is going to be bolster bracket set #CE10196G-4 which is a quantity of 4 so if you wanted 6 you would need 2 sets and you would have a couple of spares should they be needed. These are 16-1/4 inches long with some adjustability due to…

view full answer...

Answer 2

Yes the brackets #CE10002G-4 would easily support the weight of your 2,060 lb boat.

view full answer...

Answer 3

The #CE10002G-4 CE Smith Bolster and Swivel is 13" tall. Assuming you mount it at the position to gain the most height, you should have 9" remaining. Losing the height from attaching to the 3" crossmember leaves you with 10"…

view full answer...

Answer 4

We offer bolster brackets both singly and in sets of four and in a range of sizes and types for both bunks and rollers. The link provided will let you see all available parts. You can use the filters at the left-hand side of the page to select parts…

view full answer...

Answer 5

I spoke with my contact at CE Smith, and they said the Bolster and Swivel Bracket Assembly for Boat Trailers, like part #CE10000G, do not bear the weight of the boat. The U-bolt that attaches the brackets to the trailer frame support the weight of…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Can 6 of the CE Smith Bolster Brackets CE10002G-4 be Ordered

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching