Dimensions of Hangers Included with Single-Axle Trailer Hanger Kit for 2" Slipper Springs APS6SE
Updated 07/13/2016 | Published 07/12/2016 >
Products Featured in This Question
Question:
I am looking for dimensions for the APS6SE spring hanger kit. Overall sizes and mounting hole size and spacing would be appreciated. Thanks
asked by: Timm
Expert Reply:
The front hangers in kit # APS6SE are # 721584. They measure 3-3/4 inches from the top to the center of the mounting hole. The hole is 9/16 inches in diameter. The holes that are in the top are not for bolting the hanger. They are there to mount the hangers using button welds. Very few hangers are designed to be bolted on.
The rear hangers in the kit are # 721585. They measure 5-1/6 inches tall from the top to the center of the 9/16 inch diameter hole. It also features the 2 holes for button welds.
The inner width of each is slightly more than 2 inches since they are designed for use with 2 inch wide slipper springs. Both of the hangers are approximately 4 inches front to back. For hanger spacing I have included a picture that shows the possible spacing using specific leaf springs.
Product Page this Question was Asked From
Single-Axle Trailer Hanger Kit for 2" Slipper Springs - 3-3/4" Tall Front
- Trailer Suspension Parts
- Hangers
- Suspension Kits
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- Slipper Springs - 2 Inch
- Single Axle
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: front hanger
- Search Results: equalizer
- Search Results: spring hanger
- Search Results: l track
- Shop: 4-Leaf Double-Eye Spring for 3,500-lb Trailer Axles - 25-1/4" Long
- Shop: CE Smith Front/Rear Hanger for Double-Eye Springs - 1-7/16" Tall - 9/16" Bolt Hole
- Shop: Single-Axle Trailer Hanger Kit for Double-Eye Springs - 1-1/2" Front, 1-1/4" Rear
- Video: Ultimate Overview of the Single-Axle Trailer Hanger Kit for 2" Slipper Springs
- Video: All About the CE Smith U-Bolt Kit for Mounting 3,500-lb, Round Trailer Axles
- Shop: Front/Center/Rear Hanger for Double-Eye Springs - 2-3/8" Tall - 9/16" Bolt Hole
- Shop: CE Smith U-Bolt Kit for Mounting 3,500-lb, Round Trailer Axles - 5-1/2" Long U-Bolts - Zinc
- Shop: Replacement U-Bolt w/Nuts for 8,000-lb, Round Trailer Axles - 9/16" Diameter
- Shop: TowSmart 4-Way Flat Connector Rapid Repair Trailer Wiring Kit
- Video: Feature Review Front Hanger for 2" Wide Slipper Springs
- Search Results: trailer spring hanger
- Shop: Trailer Hitch
- Q&A: Upgrading Tire Size and Suspension on a Homemade Hovercraft Trailer
- Shop: Trailer Wiring
- Video: Dexter Single-Axle Trailer Hanger Kit for 2" Slipper Springs Review
- Search Results: leaf spring hanger bracket
- Search Results: hangers trailer suspension parts
- Video: Install: etrailer Trailer Hitch Receiver on a 2018 Toyota Highlander
- Video: Ultimate Overview of the Pack'Em Trimmer Rack for Utility Trailers
- Q&A: Replacement Latch for Dodge Service Body Truck
- Video: Complete Breakdown of the 1/2" Diameter Greasable Hinge Pin, 4-3/4" Long with 3/4" Base
- Q&A: What Is The Width Of The Tandem-Axle Trailer Hangers For 2 Inch Slipper Springs
- Q&A: Recommended Replacement 2" Slipper Spring Equalizer 3-3/4" Tall
- Q&A: Availability of Front Leaf Spring Hanger for 2 inch Wide Springs
- Q&A: How To Flip Square Trailer Axle For Ground Clearance
- Q&A: Bolts Needed To Install Slipper Springs





