What is the Mounting Pattern for Fulton F2 2K Winch

Question

Question:

Can you e-mail me a mounting bolt pattern for this model winch? Thanks

asked by: DB F

0

Expert Reply:

The Fulton F2 winch # FW20000301 uses an industry standard mounting pattern. The industry standard mounting pattern is basically a triangle-shaped bolt pattern. The two bolts at the bottom are 2-1/4 inches apart on center. The top bolt is 4-1/2 inches from either bottom bolt on center.

On this winch you can adjust where the center bolt is since it is a slotted hole in case you need to make some slight adjustments.

expert reply by: Michael H

0

click to enlarge

Answer 1

Hey Darrel, to bleed the Dexter Zinc-Plated Brake Actuator #T43397007K that you referenced you would need to use a 2x4 and the safety chains to push on the coupler of the actuator to pressurize it. See attached picture and also the attached help…

view full answer...

Answer 2

Yes. The Jif Marine 2 Speed Trailer Winch # will work as a replacement for your old Fulton T3205 winch. It has the exact same 5.1:1 and 12.2:1 gear ratios as the T3205 and also comes with a 10" handle. I've attached a picture for reference…

view full answer...

Answer 3

The 2-Speed Boat Trailer Winch part #315-W3200D is an excellent upgraded 3,200 lb winch for a boat trailer. In regards to mounting, not all winches use the same pattern so you'd need to compare the dimensions in the photo below to what you have…

view full answer...

Answer 4

The Dutton-Lainson Covered Hand Winch #DL17027 is going to be 10" long (at its' longest point) x 5-1/2" wide x 6-1/4" tall; the base is going to be slightly shorter at roughly 8-1/2" long and the handle is 9-1/2" long.…

view full answer...

Answer 5

Yes the Fulton F2 trailer winch part #FW16000101 is going to bolt right up in place of the F2 that you have now. It would be a super easy install. What jack do you have on your trailer? If you can let me know that I can see what you might need as a…

view full answer...

Answer 6

Hey Shawn! You can replace that A60 actuator with the Demco Channel Tongue Trailer Coupler #DM15945. This fits a 3" wide channel and 2" ball. It also features the Demco eZ-Latch which allows you to hook up when the latch is in the closed…

view full answer...

Answer 7

It seems like you have the standard 6-1/2" long oval trailer tail lights based on the photo and dimensions provided. Therefore I'd recommend upgrading to the Optronics Fleet LED Trailer Tail Lights part #TLL12RK since this would give you a…

view full answer...

Answer 8

The Fulton XLT 2-Speed Trailer Winch - 10" Long Handle - 20' Strap - Zinc - 3,200 lbs #F142425 will be able to be used on your application and winch stand set-up without any obvious issues. As long as you have clearance for the handle, you…

view full answer...

Answer 9

The CE Smith Deep V Keel Roller Assembly #CE10453G would work great to help center the boat as you load it onto the trailer as well as provide some additional support. I'd go with the wider version part #CE10455G which has a 12 inch roller on it.…

view full answer...

Answer 10

Yes the CE SMith Deep V Keel Roller part #CE10455G that you referenced will help center your boat as you pull it up on the trailer. The 12 inch version would not be overkill. Using two of these like what you see in the picture I attached will do a…

view full answer...

Answer 11

The bolts that come with the Fulton F2 winch part #FW16000101 that you referenced are 3/8 inch diameter Grade 5 bolts. I also attached a review video link for this winch for you to check out as well.

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

What is the Mounting Pattern for Fulton F2 2K Winch

Featured Help Information

Miscellaneous Media

Continue Researching