Tandem Axle Hanger Kit Recommendation that has 5-3/4 inch Center Hangers

Question

Question:

Looking at Suspension Kit APT5 w/ the 7-3/4inch equalizer and need to know if I can Have the Kit sent w/ the TREQ104 - 5-3/4inch equalizer instead of the 7-3/4. Thanks,

asked by: Kirk

0

Expert Reply:

For a trailer suspension kit that comes with 5-3/4 inch equalizers you would want the part # AP233-H248 instead of the # APT5. Aside from that and the center hangers being slightly different to accommodate the different equalizers the kits are the same.

expert reply by: Jameson C

0

Answer 1

Hey Eric, we only have standard non-heavy duty shackle straps in the length of 2-5/8 inch that you need with the part #115052. That's close enough to 3-1/8 inch that if I were you that is what I would go with instead with the part #K71-358-00.…

view full answer...

Answer 2

Hey Shaun, we have the exact replacement for your equalizer with the #TREQ104. But for shackle straps we only have 2-5/8 inch shackles in a non-hd configuration like the part #115052. So what I would go with instead is the Dexter HD equalizer kit…

view full answer...

Answer 3

To attach your axles to the the frame of the car hauler you will need the Tandem-Axle Trailer Hanger Kit for Double-Eye Springs #AP233-H248. This kit includes all the hangers, equalizers, shackle straps, shackle bolts and nuts to fit your axles. I…

view full answer...

Answer 4

Hi Mike, With the height of your equalizer increasing an inch you might need to switch to 3-1/8" shackle straps #TRSL313 to keep the leaf spring stack level but this isn't an exact science so your leaf springs could end up sitting too close…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Tandem Axle Hanger Kit Recommendation that has 5-3/4 inch Center Hangers

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching