Dimensions Of Titan Angle Mounting Bracket for Titan BrakeRite Systems

Question

Question:

pl send me dimensions lengh/heigh, with of Titan Accessories and Parts - T4821800 Angled Mounting Bracket

asked by: W.PERERA

0

Expert Reply:

I went to our warehouse and measured one of the # T4821800 angled mounting brackets for you.

The longer leg of the bracket measures 6.50 inches x 4 inches. The carriage bolt holes have a distance of 3.50 inches center-to-center.

The shorter leg measures 5.25 inches x 4 inches and the top holes are 2 inches center-to-center. The bottom holes measure 3.50 inches center-to-center.

The thickness of the material is .33 inches and this bracket weighs right at 1-lb.I have attached a photo of the angled bracket with the dimension noted.

expert reply by: Jeffrey L

0

click to enlarge

Answer 1

Hey Francis, you can email me back the picture of your actuator and I can verify what you have and if the Dexter #DX82KR will be exact replacement. If what you have says BrakeRite on it and you have disc brakes this will for sure be what you need.

view full answer...

Answer 2

Sounds like an internal issue with the circuit board which you'd have to speak directly to them about: [email protected]

view full answer...

Answer 3

I do have an option for you but we don't offer replacement circuit boards for any of our electric over hydraulic brake actuators and if I'm being honest here, that is no something you can purchase and replace yourself. If you wish to have…

view full answer...

Answer 4

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

Hey Robert, yes the Kodiak disc brake calipers part #KDBC225DAC that you referenced will replace the Tie Down calipers you have now 46304, they can be used as a left or right hand caliper and does come with ceramic brake pads. If you ever needed…

view full answer...

Answer 8

The Hydrastar Vented Marine Electric Over Hydraulic Actuator for Disc Brakes #HS481-8067 is designed to be completely plug-and-play so the female end of the 7-way would need to connect to the 7-way cable that's already installed on the trailer…

view full answer...

Answer 9

Hi Jim, the honest answer is that there isn’t a direct replacement or rebuild kit still available for the TDE LP8000, so the right path forward is to replace the entire actuator, which typically means cutting the old one off and installing a new…

view full answer...

Answer 10

The HydraStar Marine Electric Over Hydraulic Actuator w/ Breakaway and 7-Way RV Harness item #HS381-9067 is designed to work with an aftermarket electric over hydraulic brake controller. The HydraStar Vented Marine Electric Over Hydraulic Actuator…

view full answer...

Answer 11

The Demco Hydraulic Brake Actuator #DM8750311 can be used to replace your Tie Down Engineering LP8000 actuator. The Demco comes with an electric lockout like you are wanting. It is zinc coated for corrosion resistance and fits a 2-5/16" hitch…

view full answer...

Dimensions Of Titan Angle Mounting Bracket for Titan BrakeRite Systems

Product Page this Question was Asked From

Continue Researching