Availability of Replacement Brake Pads for a Titan Disc Brake Caliper

Question

Question:

I am looking for Brake pad Part Numbers for Titan 250 calipers . Are they the same as Kodiak pads ?? Thanks

asked by: Lou B

0

Expert Reply:

For Titan replacement brake pads we offer the part # T4870900 which will fit the Titan 10 and 12 inch disc brake assemblies made by Titan.

I couldn't find info on the 250 model calipers, but if you have a 10 or 12 inch assembly this would fit and work well.

expert reply by: Jameson C

0

Answer 1

The replacement for the Titan 10" disc brake assembly is the #T4870900 Replacement Brake Pad for Titan or UFP 10" Disc Brake Assemblies. Unfortunately, there is no version of the Titan brake pads designed to be more resistant to salt water.…

view full answer...

Answer 2

When Titan still made brakes the components for them were Kodiak. Since you had 250 calipers before then you can use the Kodiak calipers #KDBC250D as replacements if you want to. I have linked a video showing the features of this product for you.

view full answer...

Answer 3

I attached a chart that has the automotive cross reference for the Kodiak disc brake pads part #K2250CP that you referenced under the yellow heading. Probably the easiest to look up would be 1982 to 1992 Chevy Cavalier.

view full answer...

Answer 4

The Kodiak Ceramic Brake Pads #K225CP are the correct replacement for your #K2HR526D. If you would prefer stainless steel backing plates you could also use the #K225CPSS.

view full answer...

Answer 5

So the part number MKD289 is an automotive application for brake pads. If that's the style you need the correct replacement is the #K225CP which is the match. I attached a chart that has some other interesting info for picking out replacement…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Availability of Replacement Brake Pads for a Titan Disc Brake Caliper

Continue Researching