Recommended Spare Tire Carrier To Mount On Angle Iron

Question

Question:

CE22011Z-11050-2 I am looking for a spare tire mount for a 5X8 utility trailer. I am for something that will mount to angle iron. My wheel and tire size is 205/75/15 with a bolt pattern 5 on 4 1/2.

asked by: David

0

Expert Reply:

The spare tire carrier I recommend that can be mounted to your trailer angle iron is the Redline Spare Tire Carrier, part # 413200.

This is a weld-on installation so you can mount it to your trailer in an location you have the room. This carrier works with 5, 6, and 8-lug wheels.

expert reply by: Jeffrey L

0

Mike

5/2/2020

I have a large utility trailer. 101 inch wide. Has a utility rail and stake pockets. Which tire carrier would hold the trailer tire on side out no farther than the 101 inch width of the tires/fender?

Chris R.

5/4/2020

Are you looking to mount the spare on the side rails, or up somewhere on the tongue or A-frame? You could use something simple like the CE Smith # CE22007Z-11050-2 to mount it on the tongue, which wouldn't increase the trailer's width at all. If you have something different in mind please just let me know.

Answer 1

I do have options for you but most of our frame mounted spare tire carriers are not designed to work with angle iron. That said, the CE Smith Spare Tire Carrier for Trailers part #CE22007Z-11050-2 we have found to work the best so that's what I…

view full answer...

Answer 2

Depending on the length of your crossbars and the width of your bed yes, there is a way to mount the Yakima OutPost HD ladder rack system on your utility trailer. What you're going to need are the Yakima HD Tracks, like the 60" #Y74MR, along…

view full answer...

Answer 3

Either one is fine to do. With the Fulton Hi-Mount Spare Tire Carrier part #FSTC1000301 you are not going to be adding a great deal of width to your trailer so the difference is minimum. Giving you my opinion since there is no rule I would Choose the…

view full answer...

Answer 4

Hey Steven, The etrailer Spare Tire Mount is a high quality steel construction tire mount. The mount is torqued down 60 foot lbs onto the trailer to ensure a secure attachment for your spare. I do recommend using Loctite onto those bolts just for…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Recommended Spare Tire Carrier To Mount On Angle Iron

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching