Wire Gauge for Single 12" Wire for A91 and AL91 Series Trailer Clearance, Side Marker Lights

Question

Question:

What gauge wire is used in part # A91LW?

asked by: Brandy

1

Helpful Expert Reply:

I went out to the warehouse and pulled a single wire plug # A91LW to determine the wire gauge used. It is an 18 gauge wire so very small and thin. This is because it is designed for trailer light applications that do not draw a lot of power so a larger gauge isn't needed.

expert reply by: Michael H

1

Answer 1

When testing the brown wire on your trailer, all of the tail lights on the trailer should be activated. Since you are using a standard 4-wire harness on the trailer, you will need to make sure that you are using jumper wires to provide running light…

view full answer...

Answer 2

The Peterson Great White LED Mini Utility Light part #M290 is sealed so it can be submerged. I have attached some other like options for you below that are also submersible. Optronics Miro-Flex LED Trailer Utility Light part #UCL19CB Optronics LED…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Wire Gauge for Single 12" Wire for A91 and AL91 Series Trailer Clearance, Side Marker Lights

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching