2011 Nissan Pathfinder 4-way to 7-way Trailer Wiring Conversion

Question

Question:

On the surface it would appear that part #118267 is what I would need to complete this conversion but I believe that the existing 4-way connector is different from the one that is provided on the #118267. I have attached a photo of the existing connector. Could you please confirm/deny if it will work and if not could you point me in the right direction for a solution?

asked by: James M

0

Expert Reply:

To install a factory style 7-way on your 2011 Nissan Pathfinder there are actually two connectors that will get used. You would need the part # 118266 as it comes with the needed relays to complete the wiring.

I attached a picture that shows the two connectors that will be used to install the harness.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Prodigy P3 trailer brake controller uses a 4-wire hookup. The white wire is to be grounded to the battery negative terminal; the black power wire connects to the battery hot terminal through a circuit breaker; the red wire takes in the brake…

view full answer...

Answer 2

To install a 7-way on your 2009 Nissan Pathfinder you'd need to start with the part #118281 which is a confirmed fit. Then to install a brake controller you'd be able to use a plug and play style adapter like the #3050-P and you'd be set.…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

2011 Nissan Pathfinder 4-way to 7-way Trailer Wiring Conversion

Featured Help Information

Miscellaneous Media

Continue Researching