Installing Monitor Circuit for InvsiBrake System Through Umbilical Connecting Motorhome and Vehicle
Updated 03/12/2015 | Published 03/11/2015 >
Question:
I have a 2012 Jeep Liberty with an invisibrake system . I just purchased the 7-wire to-6wire coiled cord part no.88206 The invisibrake as a brake wire light sensor was wondering were to connect this wire on the car side connector and rv side connector . Thank you
asked by: Jorge F
Expert Reply:
The Roadmaster InvisiBrake would be installed per the procedure mentioned on page 14-15 of the installation instructions that I've linked for you. Usually, you'd just use the single wire umbilical included with the kit. You could simply zip tie this extra wire to the umbilical you purchased. If you wish, you could eliminate the umbilical, and simply wire the circuit using an unused circuit in your coiled cord you just purchased. You'd need to cut the plug off the car and the motorhome end of the monitor umbilical, and wire each side into the plug on the connectors on the motorhome and the towed vehicle.
On the towed vehicle, the wire would connect to cold side of the brake stoplight switch. On the motorhome side, you'd install the LED monitor and the emitter for the audio signal. I've linked you to a diagram showing how the monitor system is wired.
Product Page this Question was Asked From
Blue Ox 7-Wire to 6-Wire, Coiled Electrical Cord
- Accessories and Parts
- Flat Tow Wiring Harness
- Adapters
- 7 Round - Blade to 6 Round
- Coiled Cord
- Blue Ox
more information >
Continue Researching
- Shop: Vehicle Tow Bar Brake System
- Shop: Vehicle Tow Bar Wiring
- Shop: Base Plate for Tow Bar
- Search Results: rm910029
- Search Results: rm15625
- Shop: Trailer Wiring
- Shop: Brake Controller
- Q&A: What is Longest Set of Magnetic Tow Bar Lights
- Shop: Roadmaster Stop Light Switch Kit
- Search Results: 15267
- Search Results: rm15267
- Search Results: m~9000~pk
- Search Results: magnetic tow lights
- Q&A: Installing Magnetic Lighting on Towed Jeep To Allow Jeep Lights and Magnetic Light Functions
- Q&A: Do Universal Magnetic Tow Lights Have Running Light Functionality
- Q&A: Do You Need to Run a 2021, 2022 or 2023 Chevrolet Equinox at Certain Times When Flat Towing
- Q&A: Magnetic Towing Lights That Only Require A 4-Flat On The Towing Vehicle
- Shop: Roadmaster Direct-Connect Base Plate Kit - Removable Arms
- Search Results: blue ox bx7335
- Shop: Roadmaster Battery Charge Line Kit for Towed Vehicles
- Q&A: Brake Controller Install Harness Recommendation for 2017 Ford F-53 Coachmen Mirada
- Shop: Pollak 6-Pole, Round Pin, Plastic Wiring Socket w/ Rubber Boot - Vehicle End
- Shop: Universal Magnetic Tow Lights - 20' Wiring Harness with 4-Way Flat Trailer Connector
- Shop: Roadmaster InvisiBrake Flat Tow Brake System - Preset
- Video: A Closer Look at the Optronics Magnetic LED Tow Light Kit
- Shop: Roadmaster 4-Diode Universal Wiring Kit for Towed Vehicles - 7-Way to 6-Way Coiled Adapter Cord
- Q&A: Installing Brake Controller And Wiring For Towing Trailer With 1997 Coachmen Mirada Motorhome
- Video: An In-Depth Look at the Roadmaster Stop Light Switch Kit
- Video: Set up: Pollak 6-Pole, Round Pin, Plastic Trailer Wiring Socket w/ Rubber Boot on a 2019 Ram 1500
- Video: Install: Roadmaster Direct-Connect Base Plate Kit on a 2019 GMC Acadia


