See what our Experts say about this etrailer Trailer Jack

• Recommended Keeper Pins for RAM 7000 and 5000 Series Jacks
  Hey Kelly, I went ahead and checked out all of those jacks and I believe I was able to find what you're looking for. So, for # TJDP-7000-B, # TJD-7000, # TJD-7000S, and # TJDP-7000S-B, you can use the Replacement Footplate Keeper Pin for etrailer and Ram Square, Direct Weld Jacks # TJD-7000-PN; and for # TJD-5000 and # TJD-5000S you can use the Replacement Pull Pin for etrailer and Ram Pipe Mount Swivel Jacks # TJP-PN58.
  view full answer...
• Where to Weld the etrailer Jack # TJD-5000 on a Trailer
  Any where on the outside of the outer tube of the etrailer Jack part # TJD-5000 would work for welding the jack to your trailer. As long as you use a qualified welder there wouldn't be any problems with the jack warping. I attached a picture that a customer sent us that shows a similar jack welded to a trailer.
  view full answer...
  
• Trailer Jacks That Can be Welded to Sides of Trailer For Increased Stability
  We have close to exactly what you need, although a direct-weld jack such as the Square Direct Weld Jack # TJD-5000 you referenced will not be able to flip up, it will need to remain vertical where it is welded. If you are okay with that then a pair of these jacks will work great for stability so the front of your trailer doesn't pop up and the hitch ball become detached (assuming you do not exceed the 10,000 lb support capacity a pair of these jacks will give you). If you do need something...
  view full answer...
• Jack Foot Plate Dimensions for etrailer Trailer Jack
  I went out into our warehouse and measured a Square Direct Weld Jack w/ Footplate # TJD-5000 and found that the dimensions are 7-1/2 inches long by 3-3/4 inches wide. I included a video review of this jack.
  view full answer...
  
• Replacement Top Wind A-Frame Trailer Jack Options for a 16 Foot Camping Trailer
  We have oodles of jacks like the one in your picture suc has # BD155032. I have included a link to them for you. The mounting pattern is an industry standard so you won't have to weld a new jack on. What you will want to look at is the capacity, outer tube diameter, lift amount, and the retracted height. Most jacks have an outer tube diameter of 2-1/4 inches but there are some that are different. Some of the options is the link have feet or a wheel and some do not and there are numerous...
  view full answer...
  
• How Much Clearance Is Needed to Use the Square Direct Weld Jack w/ Footplate
  The clearance measurement you are referring to is largely going to depend on where you weld the outer tube of the Square Direct Weld Jack w/ Footplate part # TJD-5000 to your bumper. However, I can confirm that while the jack is completely retracted, the distance from the bottom of the outer tube to the bottom of the foot plate will be 2-1/2". Therefore, if you were to align the bottom of the outer tube on the jack with the bottom of your bumper you would only need 2-1/2" of clearance....
  view full answer...
• Is Wheel Available For Pro Series Square Jack
  All of the wheel casters that we carry limit the jack capacities to 1,200 lbs. We typically carry them for the round A-frame jacks like the Round A-Frame Trailer Jack - Sidewind - 15-5/8" Travel - 5,000 lbs # TJA-5000S-B. We do not carry wheels that will work with the Square Direct Weld Jack # TJD-5000.
  view full answer...
• Manual Trailer Jack 3000 Pounds
  The Square Direct Weld Jack 3,000 lbs # TJD-5000 is a good choice for you. This is a manual crank weld on jack with a drop leg and footplate. I have attached a review video for you to check out.
  view full answer...

Do you have a question about this Trailer Jack?