Part Numbers: 39523,3016
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
This time-delayed brake controller is designed to mount at any angle, even upside down. The controls are all up front for easy access, including a slide-bar manual override and a thumbwheel for braking output. LED indicator shows your braking status.
Features:
Specs:
The Tekonsha POD is designed to mount in any direction, and it's especially suited for mounting on near-vertical dashes. All the controls are on the front of the module, so you can still access them with the controller tucked away in a convenient place.
Braking output is the maximum amount of power that will be applied to your trailer's brakes. How much braking output you need is determined by the weight of your trailer; a heavier trailer will need more power to bring it to a stop. You want to set the braking output as high as you can without locking up the brakes. Once you've set up the brake controller the first time, you shouldn't need to adjust the settings until the trailer load changes, you switch trailers, or road conditions change. Use the thumbwheel on the side to change the braking output level. The output setting will appear as a number on the digital display, with a higher number indicating higher braking power.
The Tekonsha POD keeps the manual override within easy reach on the front of the module, great for stopping sway or controlling your trailer's momentum in emergencies. Push the slide-bar lever to activate the trailer's brakes and brake lights without you having to apply the brakes on your tow vehicle, perfect for limiting trailer movement while you re cruising.
Because inertia plays no role in the functioning of this controller, you do not have to mount the unit at any particular angle. Your mounting options are limitless, with the controller designed with all of the controls on the front of the module so you can access them even if it's mounted upside down.
If your vehicle already has a plug-in brake controller wiring harness, just connect the unit to it. Otherwise, you will need to purchase a vehicle-specific wiring harness (sold separately) to plug into. If a harness is unavailable for your vehicle, hardwiring will be necessary.
See also etrailer.com's exclusive 7- and 4-way brake control installation kit (ETBC7 - sold separately) if you don't already have a 7-way plug at the back of your vehicle.
Note: If a custom brake control wiring adapter is not available for your vehicle, a 20-amp circuit breaker (sold separately) may be required for installation.
The Tekonsha POD comes equipped with time-delayed braking. Every time you apply the brakes in your vehicle, a signal is sent - via the brake switch - to the POD. The controller then sends power out to your trailer brakes to activate them with an intensity set by you, at a rate determined by you. The amount of braking power (output) can be adjusted to suit your preference, the road conditions, the type of trailer, and the weight of your load. To determine which levels are best for your application, test your towing setup and choose what feels right.
California residents: click here
Install your electric brake controller quickly and easily with this custom wiring adapter. Simply plug one end of the adapter into your brake controller and then plug the other end into the built-in harness beneath your vehicle's dash.
Features:
This adapter plugs into the 4-pin connector in your vehicle's junction box. The box is located underneath the dash, to the left of the steering column, just above the carpeting.
To install your electric brake controller you need to connect the wiring of the controller to your vehicle. Certain manufacturers offer pre-wired options, typically known as tow packages, wherein these wires are run for you from the dash to the trailer connector on the back of your vehicle. Often, a brake controller wiring harness is included with your tow package. This harness plugs into a port beneath your dash and connects to the four wires of the brake controller. If, however, you have a brake controller with a plug in place of the four loose wires, you can use the Tekonsha adapter.
This adapter requires no hardwiring. It is designed to plug directly into your electric brake controller for the simplest installation possible. Because there are no wires to connect, installation is not permanent. You can unplug and remove your brake controller at any time and securely stow it away.
California residents: click here
Average Customer Rating: 4.8 out of 5 stars (2015 Customer Reviews)
This time-delayed brake controller is designed to mount at any angle, even upside down. The controls are all up front for easy access, including a slide-bar manual override and a thumbwheel for braking output. LED indicator shows your braking status. Install your electric brake controller quickly and easily with this custom wiring adapter. Simply plug one end of the adapter into your brake controller and then plug the other end into the built-in harness beneath your vehicle's dash.Great little brake controller for the money if you don't need heavy braking on a larger trailer. Simple and economic.
We have a Honda Ridgeline and needed this for our camper trailer. It was nice ordering the specific plug in wire for the Ridgeline and therefore eliminating hard wiring, just plugged it in. It was rough getting to the factory plug under the dash by the emergency brake petal switch. My hands are not small enough, ha ha. But success was had. Plugged into the controller and mounted it and u-wall-a. It works the way it is suppose to, I like that. A good quality unit that does what it is suppose to. thanks.
Very happy with this product. It fit nicely in my truck and plugged right into the factory wiring harness. Total installation time was under an hour. Easy to adjust, and works perfectly with my 5th wheel trailer. I simply pulled out the little storage cubby from the dash, cut the back off, slid the controller in, bolted it together, and stuck it all back in the dash. Looks and works great.
I had purchased and used the Tekonsha Prodigy P2 Trailer Brake Controller on my 2000 Silverado with good results. When I got a new-to-me 2104 Silverado, I thought I could just buy a new cable and I was correct. It was delivered quickly and plugged in with no issues. The new truck's lower dash panel is more vertical than the older truck and I didn't want to drill holes in it for the mount, so I purchased heavy duty Velcro tape and cut it to fit. It has worked without issues.
FAST SHIPPING!! Great products!!!,
I highly recommend purchasing from etrailer!! Easy to put together and install only takes minutes!! I'm using these products to pull a 30ft travel trailer and it does a GREAT job! Hooking up the distribution bars is so fast and easy they just slide in and your done, and the brake controller automatically sees your trailer and saves your settings, so you don't have anything else to do!!
Luke L.
10/22/2017
Wonderful!, it is still taking care of the job, as if it was brand new
Worked out perfectly for me, super easy installation with adapter harness. Work's flawlessly, easy one hand gain control with control's on front. My truck had nice cubby it fit in so out of the way and seamless look. Thanks for a great product and service.
Easy to install in my Toyota-Tacoma 2012. I pull my Travel Trailer and this break controller worked very well and with just a little bit adjustment. Also this item was shipped very fast.
I have a Toyota Tacoma (06). I had the controller installed in less than five minutes. One minute to gather the tools: drill/bits, screw driver, and tape. I thought tape would be helpful to hold the ground screw to the driver given the tight are under the dash. One minute to drill the ground hole. One minute to install the ground screw. One minute to plug in the cables and fish the wire under the stirring wheel to allow for the controller to be mounted in the storage area found on Tacoma trucks dash. I guess I was wrong. It only took four minutes. I did not need to put the tools away I was off to do other projects. I rate the product as good because I have not tried it on the trailer yet.
I received my purchase very quickly.
I just installed the control and wire harness today. Installation was easy, all you need are basic hand tools and a drill with a small bit.
Haven't had chance to test it out yet but, when I do I'll update.
I sell and install a variety of components for various companies and individuals. I have zero comebacks from this company. Not that I haven't received defective parts but they always make it right. And that is good business.
Did not receive wiring adapter for brake controller.
Brooke M.
3/22/2024
Oh, no, I am so sorry to hear that. I will make sure our customer service team reaches out to you and that you get your adapter.
Perfect fit. Allowed me to transfer my break controles from my Pathfinder to my GMC.
I do wish it was a few inches longer, I could had ran the wires a bit cleaner up under the dash.
Galen
1/15/2024
Still works… no issues
Smooth control. Brake action is easily adjustable while on the road. Display is clear and easily read. Very happy with this controller.
The brake controller we purchased and had professionally installed works perfectly. We had it installed in our RV for use when towing a large vehicle trailer. It's reliable and simple. It was a great purchase!
Thanks to etrailer’s video “Trailer Brake Controller Installation - 2004 Jeep Grand Cherokee”, the installation of a Tekonsha PowerTrac controller on my 2003 Jeep was very straight forward (and I’m not a car guy!). Like in the video, I used the wiring kit (#5506). I forgot to order a pigtail wiring harness but was able to pick one up locally. Took the trailer out last weekend and the brakes worked great.
Have used the power track for a year with city and interstate travel and a 4000# single axle TT. Working flawlessly on my 20 Blazer using a bypass stoplight switch.
Simple plug and play for 2019 Tahoe. Instructions were adequate and took 5 mins to install. Works great so far with the prodigy brake controller.
Received the wiring harness and bracket for the brake controller quicker than thought. Though there was a lack of instructions enclosed I found explanations on line on Etrailer site that detailed installation. The only thing missing was though the wiring harness fit, it did not snap into place. Not sure if that is correct or not. Products performed without any complications though. I would recommend these pieces to others.
The controller was a great option for our 2021 forest river FSX and gave me plenty of control over the brakes. It does require a adjustment time to time but has always worked when brakes are applied. The setup and installation were a breeze and has worked for many trips.
Easy to install, although it took a few tries to fit my hand in the small area to plug it in. Great product. Definitely recommend!
Jason
5/18/2024
A year later and I could not be happier. This was easy to set up just plug it in. Having a break for the camper has been a game changer. I cannot imagine not having one moving forward.
The wiring adapter I ordered was easy to install by following the included instructions! It is vehicle specific ,so I ordered one that fits my 2019 silverado 1500.It plugged into the 4 prong receptacle inside the block box under the dash to the left of the brake pedal against the fire wall.The other end plugged into the brake controller that I ordered(the wire adapter fits several different brands) I installed the Kenosha Primus IQ. Both items had concise, clear instructions with them.After finishing the install I plugged in the travel trailer and set the the brake controller by the instructions and it is working great!The install took me about 20 minutes.
The control works great. Nice incremental application of wheel from nothing to hard on! Led light goes from green to red also in incremental degrees. Installation was a snap in my 2008 F150 with tow package. Just Plug in the control clip and the other end in the terminal above and to the right of the computer check terminal. Rather than have it below my dash I opted for the cove below the lighter. Etrailer did a nice job of getting out to me right away and kept me informed where this was at all the way to my door. Good Job!
I ordered everything to install hitch an and 7 pin plug. Everything went great. Parts were all perfect and instructions easy to follow.
Product arrived quickly and installed very easily. Plug and play with the correct adapter (3035-P Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Ford, Lincoln, Mercury) for a 2001 Ford F-150. Controller is very easy to set the braking on your trailer.
Installed the Voyager Brake Controller on my 2018 Silverado Custom Truck. Installed quickly and effortlessly with the wiring harness. Simple Plug and Play.
Ask the Experts about this Trailer Brake Controller
Do you have a question about this Trailer Brake Controller?
Info for these parts were:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Gw
10/25/2018
No issues. Thanks.