Headlight Protection Film Specs:
Features:
Apply LampGard to your headlamps, fog lamps, turn-signal lights or parking lights and never worry about scratching, cracking or pitting again. This tough, UV-resistant cover installs in seconds directly to the lamp surface for complete protection.
More Information >Videos
for Headlight Protection Film
Help Articles
for Headlight Protection Film
Expert Answers
for Headlight Protection Film
If you were to install the EcoHitch #306-X7239 on your 2017 Ford Fusion then you would have to permanently remove the plastic underbody panel as you can see from the attached photo which is directly from the instructions. I have also attached a…
view full answer...The Yakima Replacement Hitch Bolt and Clip for Yakima HoldUp Hitch Mounted Bike Carrier, part #Y8890200, is a 5/8 inch bolt. The size wrench you would use to install or remove this bolt is 15/16 inch.
view full answer...You're right, the mounting bracket is unique (in a good way) for the Curt TriFlex NEXT Trailer Brake Controller #C24VV. The bracket is smaller and all you do is put the included adhesive tape on the bracket and stick it wherever you like…
view full answer...The Blue Ox Acclaim Non-Binding Tow Bar #BX4330 is compatible with Blue Ox base plates that are between 23" and 30" apart on center. Since you're measuring 34" on center I recommend checking out the etrailer SD…
view full answer...Yes, the etrailer SD Non-Binding Tow Bar for Blue Ox Base Plates #e47ZR would have enough adjustability between the 1-1/2" shank rise/drop and the 3" of tilt to meet your 4" difference. I've attached a video below…
view full answer...It is not recommended to reinstall the lower body fascia with the Curt Class II Trailer Hitch, #C12091, on your 2013 Ford Fusion Titanium because of the final position of the hitch once it is installed. It may be possible to mount the fascia with…
view full answer...Before deciding on a trailer to tow with your 2014 Ford Fusion, knowing the towing limitations of your vehicle will be an important factor. In the owner's manual for the 2014 Fusion, it lists the maximum trailer weight of all the powertrain…
view full answer...The 16 inches of height that the Yakima SkyBox NX 16 Cargo Box #Y95AV that you referenced would be the height above the crossbars of your 2005 GMC Yukon Denali. I attached a review video for this cargo box for you to check out also.
view full answer...When adjusting the arms of the #BWRVK3305, you have the option of setting up so the king pin will sit 3 inches forward or 1 inch forward of the axle. I'd set it up at the tallest height, 18-3/4 inches above the floor of the truck bed and 1…
view full answer...You will want the hitch to be set at the height that 1) allows the trailer to be level, and 2) allows you a minimum of 6 inches between the bottom of the trailer loft and the top of the bed rails. The fifth wheel hitches offer several inches of up…
view full answer...The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
view full answer...I recommend using the Fastway e2 Weight Distribution #FA92-00-0800 for your 7x14 Interstate Loadrunner tandem axle trailer. This hitch is rated for trailers up to 8,000lbs with a tongue weight between 400-800lbs. If your unloaded tongue weight is…
view full answer...Filter Products (2)
Contact and Help
What our customers are saying:
WOW! I am impressed! I called to place my order and real person answered, spoke perfect English, albeit a slight southern accent, and my order was sent within a day, shipped quickly and I had it a few days later. I saved over a hundred dollars over local and installed it my self. I cant imagine how that they could do any better. THANKS!
Eric
Cedar Springs, MI