The Replacement Standard Dual Rack Repair Kit for Lippert RV In-Wall Slide-Outs - Fixed Side, #LC84FR is the left side of the slide-out as looking at it, facing it, from the outside. The float side, #LC26VR, will of course be the right side as facing…
Hey Jack congrats on the new Jeep! To flat tow a 2021 Jeep Wrangler Rubicon behind your 2012 Thor Hurricane 31J motorhome, I recommend the following parts: Tow Bar and Safety Chains - etrailer XHD Non-Binding Tow Bar for Roadmaster Direct-Connect…
Hey John! Since you have the same number of teeth the Replacement 24 Tooth Pinion Spur Gear for Power Gear RV Slide Outs #LC86EX will likely work as a replacement. I would measure the outer diameter as well. If it matches the 1.417" measurement…
Hey Jared, the pass through amp rating of the Rich Solar NOVA 3K12 3000W 12V Pure Sine Wave Inverter with Built-in Transfer Switch for RVs #RS79VR is 30 amps. What AC units do you have? This should be more than enough for that.
Hey, Skip! Happy to help get your new Jeep set up for flat towing. There is going to be a list of parts, so I'll go ahead and list them all below for ya. Blue Ox Base Plate: Part #BX1139 Blue Ox Avail Non-Binding Tow Bar: Part #BX7420 Demco…
Hello Andrew, good question. Basically the only difference between the composite kits and the standard (non-composite) kits is the application they are used for. Composite are used in motorhomes, the other are used on towable campers. It has to do…
Unfortunately, I cannot tell you what wiper seal you would need for your 2004 Keystone Outback. This is not something that is known just from the RV information. It depends on your particular slide-out. The best way to determine what wiper seal you…
Hey Donna, you would have to replace the entire setup as there was a refrigerant law change in January of 2025 that forced the complete systems to have to be redesigned and because of that nothing is currently backwards compatible. So what I would…
The Fixed Dual Rack Repair Kit #LC84FR goes on the left side of the slide as you look at the slide out from the outside of the camper. So on the drivers side it will be the front of the slide. The Floating Dual Rack Repair Kit #LC26VR is going to be…
You've got both a wiper seal and a bulb seal here with the wiper seals having a track for the bulb seal to slide onto. The Rubber Wiper Seal with Track for RV Slide Out #SR87FR you were already looking at is most likely the closest option to what…
In order to determine if the correct Lippert Replacement Hydraulic Cylinder like part #LC339031 you would need to measure the distance between your hydraulic fitting ports and note the color of the cylinder. The above Lippert Replacement Hydraulic…
Hey Kyle, yes the Flair-It High Pressure Hose #FL37FR does fit on the 1/2 barb fitting of the Flair-It PEXLock Female Elbow Fitting #FL44ZR that you also referenced.
WOW! I am impressed! I called to place my order and real person answered, spoke perfect English, albeit a slight southern accent, and my order was sent within a day, shipped quickly and I had it a few days later. I saved over a hundred dollars over local and installed it my self. I cant imagine how that they could do any better. THANKS!
RV Slide Out Parts for Lippert In-Wall RV Slide-Out Systems
Count on exact-fit replacements to keep Lippert In-Wall RV Slide-Out Systems running smoothly. Match your motor and controller by gear ratio—300:1 or 500:1—and note that moving from 300:1 to 500:1 won't add performance or longevity. If your setup uses the round-square plate, that motor can be obsolete and a full system change may be needed, and some installs are best handled by a technician.
Yes, the 500:1 option can replace a 300:1 as they share dimensions and design. The difference is torque, but you will not see any benefit in that both will operate at the same pace and strength. Replace motors in pairs on the same slide to keep them matched. Confirm your controller and harness connections before ordering.
Match the motor's gear ratio and mounting style first. Check whether your system uses 300:1 or 500:1 gearing and confirm round-round vs round-square mounting plates; round-square plate motors have become obsolete and may require a new system. Verify the connector style; some motors use a 6-pin plug. If unsure, compare your removed motor for an exact fit.
Pair the controller to the motor's gear ratio and plate style. Older controllers are compatible with 300:1 and 500:1 motors used on round-round applications. If your setup is round-square, that motor style is obsolete and you'll need a new system. Verify your harness style; some motors use a 6-pin connector that must match the controller.
Plan on a pro-level job rather than a simple DIY. Support the slide properly and sync the system per the controller instructions. If adding rollers, check bracket tabs—some needed grinding so they wouldn't gouge the slideout floor. In cold weather, operation can feel a bit sluggish, which can be normal. Confirm exact-fit parts to reduce rework.
Controller Parts
RV Slide Out Parts Parts or Accessories
Filters
