The Replacement Standard Dual Rack Repair Kit for Lippert RV In-Wall Slide-Outs - Fixed Side, #LC84FR is the left side of the slide-out as looking at it, facing it, from the outside. The float side, #LC26VR, will of course be the right side as facing…
Hey Stephen, we have the 16 foot etrailer awning part #e84QV that would work great on your car hauler. How tall is the side of the trailer? It shouldn't be a problem but the arms of this awning are 69 inches tall. We spent a lot of time on our…
Hey John! Since you have the same number of teeth the Replacement 24 Tooth Pinion Spur Gear for Power Gear RV Slide Outs #LC86EX will likely work as a replacement. I would measure the outer diameter as well. If it matches the 1.417" measurement…
Hey Jared, the pass through amp rating of the Rich Solar NOVA 3K12 3000W 12V Pure Sine Wave Inverter with Built-in Transfer Switch for RVs #RS79VR is 30 amps. What AC units do you have? This should be more than enough for that.
Hey Donna, you would have to replace the entire setup as there was a refrigerant law change in January of 2025 that forced the complete systems to have to be redesigned and because of that nothing is currently backwards compatible. So what I would…
Unfortunately, I cannot tell you what wiper seal you would need for your 2004 Keystone Outback. This is not something that is known just from the RV information. It depends on your particular slide-out. The best way to determine what wiper seal you…
Hey Kyle, yes the Flair-It High Pressure Hose #FL37FR does fit on the 1/2 barb fitting of the Flair-It PEXLock Female Elbow Fitting #FL44ZR that you also referenced.
Hello Andrew, good question. Basically the only difference between the composite kits and the standard (non-composite) kits is the application they are used for. Composite are used in motorhomes, the other are used on towable campers. It has to do…
Hello Sandi, Thank you for sending over the pictures. They were very helpful in confirming the correct replacement. Based on the photos, the Lippert Replacement RV Slide-Out Venture Actuator with 18:1 Motor, 24" Long #LC119128 will work as a…
Hi Frank, The In-command system does limit our options for what air conditioners we have that'll work with that system. You can replace your Coleman AC with the Dometic FreshJet 3 RV Air Condition part #DMC94JF and install the Dometic Climate…
Hey Derek, We do have what you are looking for. The correct replacement for the 1510000236 is the Replacement Auto-Programmable Controller Panel #LC26TF. What RV do you have?
You've got both a wiper seal and a bulb seal here with the wiper seals having a track for the bulb seal to slide onto. The Rubber Wiper Seal with Track for RV Slide Out #SR87FR you were already looking at is most likely the closest option to what…
Keep your room moving and sealed with RV slide out parts. Choose from seals, motors, controllers, pumps, and trim, and match fixed and float side components—the Fixed side is the left side when facing the slide-out from the outside, the Float side the right. Measure the arm to size gear packs, use a small amount of seal lubricant to help rubber slide in tracks, add the o ring during install, and if a slide fails, check the ground wire first.
Yes—use a small amount of seal lubricant to help the rubber slide in the tracks. Too much can make it hard to grip, so keep it light. Tight spaces can slow things down, so work patiently and feed short sections at a time. Double-check orientation so the wiping edge and bulb face the right direction before you commit.
Pick a seal that matches your original profile and thickness for proper contact. Thicker, more solid rubber helps resist wear better than thin, flimsy material. Order a little extra length to allow slight overhang so you don't see daylight at the corners. If your seal slides into a track, confirm the track style matches so it can seat correctly.
Measure the slide arm to determine the correct size for your system. When swapping the pack, use a floor jack with a wood block to lift the slide box slightly to take tension off the assembly. Keep hardware organized and verify the arm style matches what your system uses before tightening everything down.
Confirm the track orientation matches your original; some tracks point a different direction and won't take the cover. If the cover won't fit, seal each screw head with caulk to protect the bubble seal. Check alignment before drilling so the wipe and bulb seals aren't pinched.
Start by inspecting the ground wire for corrosion and a solid connection. Clean the contact point, replace a damaged end, and use a new screw if needed. Verify you have 12V power where it's supposed to be. These quick checks can save replacing a controller or switch that isn't the real issue.
Filters
