# 1
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
just as described on their web site. Fits the trailer hitch and very satisfied. Only thing I would recommend being purchased with the trailer hitch is instead of the normal pin with carter pin. I would advise purchasing a key locking pin so that no one can steal your draw-tite ball mount and also steal the replacement mount you purchase that slides into the slot when towing anything, People have had there College Logos stolen because they did not have a key locking pin to avoid anyone just walking up undoing the carter pin, pulling the pin and walking away with those and the hitch cover. So if ETRAILER.COM sells the locking pin I would purchase it from them instead of the normal pin.
Product was fine and did what it was supposed to do.
# 2
Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
from E-trailer...and once again I'm very satisfied! The package was delivered within a few days of ordering, all the contents were included, & the videos made for a flawless self-install (& I hate to admit it, but I'm not the most handy at things like that!). I have & will continue to refer friends & family to E-trailer for any future needs.
good value and quality. Came with 2" ball and pin.
# 3
Draw-Tite Drawbar for 1-1/4" Hitches - 5/8" Rise, 1-1/4" Drop - 7" Long - 3.5K
Items packed well delivered on time. Doesn't get much better that that.
Product arrived within three days and was the correct size I needed. Quality is good. All my hitches have had 4" bars but this one needs a 2" bar.
# 4
Curt Class II Drawbar - 3/4" Rise, 1-1/4" Drop - 9-3/4" Long - 3,500 lbs
It works very well
looks good and fits
# 5
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
Longer stinger let me drop the tailgate on my Tacoma with trailer attached. Replaced a similar but shorter Curt hitch and both are very substantial and well made for the weight of my trailer.
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
# 6
Hidden Hitch Ball Mount - 3/4" Rise, 2" Drop - 15-3/4" Long - 6,000 lbs
Ordered this hitch and it worked perfect for what I needed just bought a teardrop trailer. Couldn't open up the tailgate on my Jeep so I ordered this extended hitch and I brought the ball out past my spare tire and the tailgate opens up now I have no problems. And I looked everywhere couldn't find one of this quality and at this price very reasonable the other ones hundreds of dollars didn't want to spend that much.
This was the longest hitch ball mount I could find anywhere. I used it with a short extension for my 2021 T G so that I could open the back doors without hitting the trailer wheel crank. With my new trailer, Intact Flyer Discover, I don't need the extension and can still open the doors. Works well.
# 7
Curt Class II Drawbar - 3/4" Rise, 1-1/4" Drop - 6-3/4" Long - 3,500 lbs
It works very well
looks good and fits
# 8
Curt Towing Starter Kit for 1-1/4" Hitches - 2" Ball - 3/4" Rise - 3,500 lbs
Keep with spare tire out of weather to prevent rust.
Delivered missing the retaining clip
# 9
Curt Class II Drawbar - 3/8" Rise, 1" Drop - 7-13/16" Long - 3,500 lbs
It works very well
looks good and fits
# 10
Reese Trailer Hitch Starter Ball Mount Kit
I needed an very specific ball mount(class I, 1/2" rise, 2" ball). etrailer had what I needed in stock and available to ship next day. I had the thing ordered in 60 seconds. Wish I wouldn't have waisted my time and gas shopping at my local hardware stores only to find they didnt have what I needed.
# 11
Convert-A-Ball Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10,000 lbs
this is the second cushioned ball mount I have purchased. I haul a specialty trailer daily for work, stop & go, rough terrain first ball mount I used was just a cheap hollow one witch was turning the pin hole on the truck into an oval. Bought a cushioned ball mount and it lasted 4-6years of towing 3-5days/week before one of the pins holding the cushion in finally corroded in half. I'm sure the pin could have been replaced with some work to compress the rubber again but for the price and longevity of the product I just ordered new and keep on going.
Rock Solid and so Smooth I can't give enough praise to this much needed item. I was in a rush to get this during the holidays because my previous mount was thrashed and I was going on a big trip. It shipped the same day at 4pm about an hour after I purchased it and arrived on the 5th day nicely packed and everything I ordered was there. My trip was over 200 miles with about 3,000 lbs on some rugged potholed fire-road bumpy terrain for most of it. I love the "cushion" feature... No more clankity clank - jerkity jerk from the hitch. I'm curious as to it's longevity before the cushion becomes sloppy and I plan on taking it all the way there. I also purchased the stainless interchangeable balls and say this is a must have. The 12" drop is perfect for an 8" lifted truck. This was my first experience with etrailer... And it won't be my last!
What our customers are saying:
"Excellent service and communication. Expect part to be excellent too!"