Most Popular Draw-Tite for 2021 Toyota Tacoma

Pretty solid build quality, and everything fitted together well. The instructions were clear enough, but I found an eTrailer video on YouTube which helped a lot. I think the installation time estimate is a bit optimistic. With the front wheels on my 2021 Tacoma TRD Sport up on ramps, I took around 2 hours to finish the job. If I had to do it again, with a helper, and I had a lift like in the video, I'd guess an hour would be reasonable.

Had to touch up the paint on a dozen or so spots that were chipped down to bare metal. Bolt Torque spec will crush your frame. It's ok on the other bolts. Provided frame plates are not sturdy enough to prevent bending the frame. Directions didn't say the frame is supposed to crush. Maybe Toyota lightened up on the 2021 Tacoma frame steel. Otherwise the receiver is very good.

Great products, great prices, fast shipping and a great company to do business with. Easy install, and it took longer to trim the air dam than installing the hitch.

Click to Enlarge

Click to Enlarge

Terrible, they sent the wrong hitch and now want me to pay shipping for the return

I bought this receiver to add front mounted 'accessories' on my 2007 Jeep Wrangler Unlimited Sahara. I plan on using this to add an extra bicycle rack, a cargo basket, a receiver mounted winch or other 'accessories' needed for my Jeep when I take my family camping. It will also be useful for "front launching" a boat or parking a trailer in tight spots. It took me about an hour to install, although I had already previously removed the lower wind deflector cowling, so did not have to spend time removing it or cutting it for a finished look. Detaching and moving the top trim panel between the grill and the bumper is a must to facilitate the installation. The receiver fits pretty close, although you do have to manipulate it to get the holes to line up with the frame. Follow the instructions and do not tighten any of the bolts until you get it lined up and all the bolts in loosely, then torque it down. As noted in the instruction sheet, the driver's side of the receiver does not sit flush against the frame, there is about a 1/4" to 5/8" gap. The instructions say to use the extra split washers (in the kit) as filler, but they would just rattle around loose in there and provide any benefit, so I omitted them. Once tightened down, the receiver tube was not parallel to the ground, it is slightly higher in the front, sloping towards the rear. It is not off enough to affect my intended use, but may be bothersome to those with type 'A' attention to detail. Overall a good product that will add a lot of flexibility to my Jeep~

Click to Enlarge

Click to Enlarge

Click to Enlarge

Relatively easy install. Just have to be mechanically inclined. We use the hitch to carry a fish rack/cooler on a 2011 Jeep Wrangler. So far so good.

Road tested 4000 miles & off-road, Solid, Great ! I always wanted a front hitch, it is rad ! We had a great experience across the board. Ordered the front hitch mount and had a mechanic (Weld Tech/San Diego) install it, because they already had our van to install their lift kit. They charged me one hour labor. I can see that it fits well and is solid. We went on a 4000 mile adventure with a small motorcycle on the front hitch. etrailer has been a good source for for a few things now.

Click to Enlarge

Click to Enlarge

I own a 2003 Ford E-450 RV cutaway and wanted a front hitch to carry our bicycles since our rear hitch is used for a trailer. I originally tried to mount the equivalent Curt front hitch, because of its cheaper cost, onto the vehicle. However, the Curt hitch wouldn't work because it can't adequately accommodate the slight downward hump in the truck's frame. This hump can barely be seen between the two hitch mounting bolts. The hump is on both the left and right side frame rails on my vehicle. If your frame is not totally flat (has even a small hump) you cannot use the Curt hitch. The Curt's small indentation on its mounting flange will not adequately accommodate the frame's hump. This Draw-Tite hitch, 65001, mounted perfectly on my vehicle and the installation procedures I used were exactly as depicted in the etrailer video for the E350 van. In the video, the technician uses a rotary file to expand the rearward holes to allow the insertion of the bolts. I had to do the same thing and bought a rotary file for my drill at my local home improvement store for less than $3. I did not have to use the rotary file on the forward holes. In addition, I have the larger Roadmaster front sway bar and steering stabilizer and as you can tell in the photo, there is plenty of room for the hitch.

Click to Enlarge

Added to use with a front winch. The install was not too difficult and the included instructions were spot-on. On my F250, the front tow hooks add to the strength of holding the hitch to the frame. On the F250 you do lose the OEM fog light location, but I used the wiring to add/relocate after-market fog lights. The set up has already proven helpful, pulling me out of a snow back while plowing. Just what I needed for some summer off road camping as well.

Click to Enlarge

Click to Enlarge

Click to Enlarge

I chose this product because it was among the more inexpensive front hitches I could find. I plan to build a t-bar for it and use it in conjunction with a homemade headache rack to carry 16 foot garage doors. Like other reviews and vids I have found, the bolt up is hard. I reversed the bolts and use the new ones on the outside, as well as removing my grill. My truck is a 2003 - so not much room like the 2008 and newer trucks.

Click to Enlarge

I chose Draw-tite because they are built very well and this one is no different. The welds are done well and I have no fear that this product will serve me well. The install wasnt to bad for a DIY type like me and the fit was excellent, only took a few hours. Knowing that I can now be pulled out of a bad situation or pull someone else out is comforting with the help of a hitch mounted winch. The Price was right and etrailer shipped it out fast although packing could use a smaller box . Oh yeah, UPS sure tested the toughness of this receiver ! . Great product and great service from etrailer

Click to Enlarge

im very satisfied with my front receiver. ive used it as a recovery point,to move trailers, and as a mount for bike rack and cargo holder. if i had a winch platethat would be very handy too. etrailerhad a fair price, quick shipping, and overall great customer service. i would use them again andrecommend to a friend as well.

Ordered the same hitch from Amazon, and showed up not J-Pin ready, with (1) hole drilled for a hitch pin against the weld. Can't run the nut flush because of the interference with the weld bead, and no 7/16" hole present. Returned it. Ordered another one from etrailer direct. Called in the order to make sure they QC'd prior to shipping. Assured me they would. Box never opened, and the same nonsense showed up. Not happy, trying to work it out.

Fit Perfectly, super easy to install, and super fast shipping! Holds Hollywood Bike Rack Great and very solid for my two E-bikes. Thank you etrailer!

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

After a year of having this on my truck I can say that I wish I did it sooner! The installation is easy as can be. The hitch is super handy as both a tow point and also as a kind of skid plate/bumper. I have contacted multiple ecology blocks and other objects in my truck, the hitch is the first thing to touch so nothing on the truck gets damaged! This is a super strong, affordable, and versatile addition to any vehicle!

Click to Enlarge

Click to Enlarge

Click to Enlarge

VERY Easy install - not quite centered but that's no biggie - Used it already to fine tune the travel trailer into it's tight parking space. Also will be used for carhauler/utility trailer parking and canoe hauling and bike hauling and winch mount - Multi use deal! ; )

Click to Enlarge

I buy practically all my towing accessories from etrailer. One of the reasons why is that you can tell that they take the feedback of their customers seriously. I read a lot about previously shipped products having fell out of the box in certain areas. etrailer heard that feedback and my shipping box was reinforced in just the right areas that were talked about getting punched through in shipping. The tech notes video on the 2012 F-250 applied exactly on my 2016 F-250. All the measurement specifications were correct as well. This is a job that can be done by one person, albeit you'll have to be careful. Your second set of hands can be jack stands, as it was in my case. If you take your time in positioning everything - installation will be a breeze. I do agree with previous reviews - it would be nice to have a second fishing wire as it does get stretched out when pulling the first bolt through. That, or a heavier duty gauged wire - that's just a small detail however. If you're really concerned about it, you can buy a secondary fishing wire at around 5 bucks. I spent more time taking out and putting back in body clips than I did with the install of the hitch receiver hardware. I really like the way it looks and I'm excited to use it.

Click to Enlarge

I plan on installing it tomorrow, however first impressions are not good. The box it item was shipped in was extremely damaged. Torn, ripped and taped up on all sides. The delivery person said that due to the sharp edges and the face it wasn't secured in the box (lose) led to the damage. It appears the item was not packaged properly. I just hope all the parts are there. More to follow.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

This was one of the easiest accessories I’ve installed on my Tundra. It is a front receiver hitch so I don’t use it very often. Mostly just for bike racks when towing a trailer, but when you need it you need it.

These is an excellent hitch at an excellent price. The install was easy and all the hardware that is needed is in the box. I chose the Drawtite over the Curt because the receiver end is a little longer. It' not even noticeable on the truck. I have a snow plow that attaches to the hitch. The Toyota cap shown in the picture was not included. The Tundra is a 2020 so I can confirm if fits.

Click to Enlarge

Click to Enlarge

Click to Enlarge

It installed as advertised and fits perfectly. I haven't used it yet, but it will make positioning my trailer in my backyard much easier!

Would like to just take a moment To thank etrailer for getting our draw tight front mount hitch and our swagman bike rack to us. It certainly solved our problem. For sometime we have wanted to take bikes camping with us and have not had a proper place to haul them. The camper has a molded bumper and I certainly didn't want to haul them in the camper. So my hat off to you on both products

Click to Enlarge

I'm off to overland in Texas and wanted you to know that the hitch and winch carrier are perfect. Using quick connectors, I can use ir on the front and rear. Removing it also saves on gas. It works great with a moulded number, saving on buying a specialized steel bumper and other expensive attachments. I like that I can still have all the internal mud guards and brush cover without having to take them off and not be able to have them on. Awesome!

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

This is a high quality hitch that fits the Gladiator perfectly. The hardest part of the installation was removing and reinstalling the push fasteners on the plastic air dam. While the hitch fit is perfect, the instructions for cutting the plastic air dam leave something to be desired. I finally had to eyeball the location for the hole and then found that the suggested utility knife simply wouldn't cut the plastic air dam. An oscillating saw solved the cutting problem easily and the best guess location worked out. Am I happy with the end result? You bet! Would I do it again? Absolutely.

Click to Enlarge

I installed this on the front of a 2018 F350. Fit an finish is great. Install was easy and directions simple to follow. Having another set of hands was very helpful, else it would be a balancing act I imagine. No drilling needed except for the cutout in the valence. My use is a cargo basket for four bikes and a kayak rack when pulling my fifth wheel. I have a receiver splitter that allows me to have both the basket and Yak rack mounted at the same time. Load up the toys and go...

Click to Enlarge

A tight fit with the bash plates on my 2023 Ford F250. I also cut a 3 inch square air dam hole instead of 3 1/2. But had to extend the top of the hole due to the slope of the dam. The hitch pin hole barely clears the air dam. The hitch pin clip will rub on the air dam.

The hitched arrived three days early and I was able to install it in less than 2 hrs with a little help from my wife and a floor jack. Perfect fit!! No shimms necessary Vwrry happy.

The hitch installed easily on the front of my truck and has given me more versatility in using my truck. In the summer I carry 3 bikes on a hitch rack when I go camping. I also hook up a 12000 lb. winch when needed. Sometimes I use the front hitch when moving my boat. This is a very sturdy and reliable hitch. Etrailer customer service is excellent.

Click to Enlarge

Easy installation, nice sturdy hitch that fits on the front of our C- Class RV to haul our electric bikes. Highly recommend it.

Click to Enlarge

I ordered this literally less than 24 hours ago and it arrived to my doorstep!!! I think etrailer needs to call Amazon and tell them how it is done. Like honestly, I am not even prepared to put it on yet as I was expecting a week for delivery! Holy cow, do you all sell groceries as well?

The packaging needs additional crush protection. While it’s difficult to damage a trailer hitch, the box was mangled and the hitch is missing paint and has jagged edges of flaking paint all over. I’ll spend time repairing the finish on the hitch after paying good money for what should’ve been a product in brand new condition.

Click to Enlarge

Perfect fit on my 2020 Chevy 2500HD. I didn't even have to trim the lower plastic spoiler. Install took about 20 minutes. Can't wait to try it out for my motorcycle carrier. As always, etrailer gives great, speedy service.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge