Most Popular Round Bars for 2021 Toyota Prius

I put the rollers on a strong arm loader it Works great, the loader fits a 2in receiver it pulls backwards at a 45 degree angle and it is springs loaded you put the kayak onto it then go to the back of the kayak push forward and the kayak is at a 45 degree angle in the air then you push it's on the rollers and stop when you get where you want it let it down gently a d that's it ,take it off in reverse thanks to the wheels it makes it very easy

Click to Enlarge

These Handrolls were a replacement for ones about 30 years old which worked great but the rubber/plastic was degraded by the sun and the degraded plastic would get on the kayaks. The wheels of the new HandRolls do not turn well, even with an overabundance of Silicon lubricant sprayed inside. They worked very poorly in loading my kayaks. They will soon join their brethren in the dumpster.

Wry disappointed in such an expensive rack and kayak carrier. It is extremely difficult to reach the carrier to place two kayaks. We are very uncomfortable transporting the kayaks for longer and highway travel. I would not recommend these to others. We likely will purchase something other in the future. I’d rather put the kayak in a car or pickup truck that they would fit in.

We bought this Kayak rack for my mom to put on her 2016 Jeep Grand Cherokee so her and my dad could haul their kayaks easier. The mounting hardware was a little tricky at first but once we figured it out, it wasn't bad at all. It holds the kayaks in place nicely. Had no issues with them getting loose or moving around. Seems to be built well and they're very happy with it so far.

This kayak carrier works great with my factory Rav4 roof rack and 10' Tamarack Angler kayak. I did break one tightener knob but probably over-tightened it. And it was replaced for free. I can load and unload the kayak easily and it doesn't budge going down the freeway. I can even drive in and out of the garage with the kayak on the rack for easy storage hanging from the rafters.

Click to Enlarge

Installed this Thule Top Deck Rooftop Kayak Carrier System with tie onto our Thule Roof rack system. Easy to install and this will carry our handmade 17' Wooden Sea Kayak. Very well made.

Easy to install and looks great!

We needed a better way to haul around 3 kayaks and after looking at a number of options, we settled on the Thule Stacker setup. Installation is simple and the stackers provide a sturdy option for hauling multiple kayaks. One of the best features is that they fold down when you don't need to use them. My shopping experience with etrailer was smooth and shipping was prompt.

Click to Enlarge

These work great and I was able to install them on the OEM rack for my truck. The only downside is that the threads for the clamp hang down a little too close to the roof for comfort.

The Rhino-Rack 2 Kayak Carrier I ordered from etrailer was easily reviewed and ordered from their website and ALL communication relative to order confirmation and extreme detail included in their tracking was nothing short of phenomenal! The items were packaged with care and arrived intact. These fit our basic Lexus crossbars and is the perfect product for carrying our two (2) kayaks. My hat goes off to the great folks at etrailer -- It doesn't get any better than this!!!

Needed a rack to haul my kayaks on my jeep patriot and this price was unbeatable. Works well, though I did not like using the foam blocks. Good first rack for new kayakers.

We needed a carrier solution that folded down easily because of our garage door height. The Malone Pro2 Kayak Carrier has performed flawlessly over the past year. The kayaks remain stable and never shift even at freeway speeds. The foam blocks fit our crossbar well and offered a rattle free ride, which is nice. The one drawback to this system is how difficult it can be to actually route the straps. Without a ladder, it can be nearly impossible to get the strap over the kayak and hooked into the carrier properly. After you find a system that works for you, it becomes easier but I still think that the stationary carriers are more user friendly in that regard.

After attempting to mount the individual rack pieces using the “burglar proof” button head screws with the pin in the recess and the short hex wrench with the hollowed out end I discovered that no real burglar would want the rack but would rather have the kayak so the first thing I did after spending 10 minutes trying to insert the hex into the button head screws with the pin inside the recess and attempting to turn the bolts and continually being obstructed by the support pieces and the paint interference on the bolt heads with trying to get the wrench into the recess I knew it was going to be a long frustrating process so I threw them away and purchased new button head stainless steel bolts and a 4mm extended handle hex wrench to turn them. Smartest thing I ever did. You not only have to mount the rack initially but then you have to put the kayak on the roof and remount all pieces again to fit your boat. All kayaks are different to one degree or another. Having to move the individual support and retighten them with the boat on the rack is even more difficult to do than the initial mounting with these “burglar proof” bolts and hex wrench and you will be happy you threw them away before you started the entire process. Try it for yourself at first and then go get the alternate ones. Worth the little investment and stainless steel will not rust away when you want to remove the rack system in the future. Once the rack is on your vehicle and kayak in rack the tie downs supplied are very good quality. Make sure you use the recommended tie down locations and directions, two kayak body ties and ties at front and rear. Due to numerous kayak hull designs it would be nice to have each support pod have a horizontal swivel built into it so it readily conforms to the hull shape. The overall quality of the system should be the last rack you will have to purchase. I only had issues with the supplied bolts and hex wrench. I gave this rack system a three star because of the bolts and hex tool and the individual pods not swiveling and I haven't at this point transported the kayak anywhere so I am waiting to see how it handles long trips with wind loads and constant loading and unloading performances.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Perfect for strapping the board to the car to catch some waves. Fits my Prius C perfectly. Have been VERY pleased.

I love this rack! I don't think I'll ever take it off my car. Cool and functional. I've used it for my snowboard in the winter and my surfboard and camping gear in the summer.

Click to Enlarge

While the quality & construction of the Thule Hull-a-port 834 kayak racks are excellent, I did have some issues with the method recommended for attaching them to my Thule Wingbar Evo bars. Although I was told the components were compatible, I was not told that an adapter kit was required which involved attaching each section with 36 small parts (bolts, nuts, washers, etc). Nothing rapid about this. The good news was, etrailer's customer service was excellent, and they arranged for me to return the kayak rack & purchase the Hull-a-port XT 848 instead.

Arrived quickly and was very easy to assemble and attach to the roof of my Jeep. Now that I have the initial setup complete with the proper placement of the entire system, attaching and removing the kayaks will be a breeze. Will definitely make hauling our kayaks much easier and safer.

Click to Enlarge

The product seems great but I have not figured out how to get it safely attached to my bars. I have an Agricover Adarac on the bed of my truck and the crossbars are 1-1/2 x 1-1/2 inches square. I thought this would work well since it's for up to 3-1/2 x 1-11/16" crossbars, but it isn't secure on these. I'm going to try and figure out an alternate method for attachment though. Thule Hull-a-port Pro's are the perfect (mounting) solution but don't seem to be made any longer.

Click to Enlarge

Great product and great customer service! Very easy to install, but I highly recommend to watch the installation video first. We used typical black office clips to clip the excess straps down since they came untangled when driving. Also, I recommend to purchase locks for the racks since we are concerned someone may steal them because they are so easy to take on and off.

The product is of good construction but probably due to how it fits on my crossbars it needs additional support. The crossbars for my Honda Pilot are wide blade type and these racks seem more appropriate for narrower square type crossbars. Even with the rack fastened very tightly, the rack can twist back and forth. Last year on a trip across Montana the wind was pretty gusty and it caused the front one to pivot quite a bit and we had to pull off and apply a ratcheting strap over the kayak and under the factory rails to ensure it was held tight and wouldn't move again. This year on the same trip we had bad winds but had a roof rack mounted behind these racks giving it support on the tall side. We had to strap it real good to make sure it didn't move. If we hadn't had that additional support behind it and add'l straps we probably would have had more problems. I think if the top metal bracket had a wider channel to fit our crossbars it would be much more stable. The way it is now it just sandwiches 2 metal plates between my crossbar which allows it to pivot under stress.

Click to Enlarge

Loved the racks, seem very durable. Only downside was that the groove made for the crossbeam was quite a bit smaller than my crossbeams, but they still secured down great. You'd have to have a pretty funky set-up for these racks to not work on your vehicle. Having all the straps/tie-downs included was awesome too. Reccomend!

Click to Enlarge

Trevor made the recommendation,great rack covers thanks ,thanks again!

Here are some more pics. Very happy with the racks, tie downs and pads. Easy to install, very secure. Love the straps. They have protection around the buckle to protect the board and built in velcro to hold the straps together when not in use.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

These pads worked well on our Yakima RailBar Crossbars- Item #Y00448-0449 that we also bought from etrailer around 2020/2021. Not sure if etrailer carries the exact Yakima Crossbars anymore, but think they have a similar model. Both the pads and crossbars work well to haul our kayak on our 2019 Subaru Forester. etrailer's customer service rocks! We had a lot of questions purchasing both items and they were great to talk to!

Click to Enlarge

Click to Enlarge

Click to Enlarge

The product came quickly and was so easy to install on my existing roof rails! It is absolutely perfect to fit many needs above and beyond my kayaks and paddle boards. They look so good on my new 2019 Jag F-Pace I might leave them on all the time.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

I love my Rack it came when promised and etrailer was great believe me I will be going back to them for anything else I need I am giving them a well deserved 5 stars

Click to Enlarge

Click to Enlarge

The only thing better than the quality of the product was the quality of etrailer’s customer care. I had to return the Thule SUP Taxi because it was too difficult for me to tighten the straps with my arthritic hands, these wonderful folks were completely obliging, helpful and courteous!

Brought home a new kayak yesterday using this J cradle for the first time. Easy to set up and load. Two complaints: not impressed with the strap buckles - had to tie knots to secure. And the 3-inch bolts weren’t long enough to easily attach the cradle to my Rhino Rack crossbars, so I had to replace them. Also got my finger pinched pretty good adjusting the cradle knobs - my fault for not being more careful, but just saying …

Click to Enlarge

Great product for the price - The cradles were very easy to mount (and lay flat once folded). The videos were helpful in showing how to set the straps in the most efficient way. I test-drove my car today with my fishing kayak on top on a 80-mile round trip (a mix of freeway, country road and dirt tracks). The kayak was perfectly still, no particular wind noise and I was able to muscle to kayak up the roof and take it down on my own (it's a 52 lbs boat). I really recommend that product and I'm glad I went for J-Style cradles!

Click to Enlarge

The Rhino Rack cradles, straps and hardware are all good quality and I have no complaints. The only issue I have, and the reason for only a 4 star rating, is the supplied M6 x 40mm Security Head screws are too long for the factory cross bars on my roof rack. When I first installed the cradles if I had tightened the screws all the way, the ends would have dug into the roof and paint, even before I added the weight of the kayak. In checking, I can purchase some M6 x 25mm Security Head screws from Amazon, but frankly part of me feels that for what I’ve already paid for this kit I shouldn’t have to spend another $15 for the correct length screws, plus the package has 20 screws and I only need 8. However, it appears that is exactly what I will have to do. At least they will be stainless steel, rather than the cheaper material the current screws are. Plus I will have extras for when/if the head strips out. I would suggest Rhino Rack consider included in their kit two sets of screws to meet this need. Keep the length they have, Judy add a set of 25mm. I’m still happy with the purchase but not 100%. I do like how the kayak slides easily on the rear felt lined cradles. Plus Rhino Rack includes every tie down strap that you will need, e.g. one each for the bow and stern in addition to two straps intended to secure the kayak directly to the roof rack cross bars. I would highly suggest you get in the habit of using all four straps, you really don’t need to have a gust of wind lifting the nose and tearing the roof rack off your vehicle. Can happen! My brother-in-law lost his roof rack exactly in this manner. So happy yakking and safe travels down the road. By the way I have paired these cradles with the Rhino Rack RTL002 T-Load Hitch Mounted Load Assist and Support Bar for 2” Hitches also purchased from eTrailer. I’ve attached some photos showing my first and second attempts to solve my dilemma. I need to order the replacement screws. First attempt after dark was a large flat washer, then the next day I added some nuts under the large washer. NOTE: Photos may post in reverse order.

Click to Enlarge

Click to Enlarge

Bought a pair of these to go on 59" rhino rack bars on our Outback Wilderness and am really pleased. I left the bars full width - they are not a head banger on the car - and mounted the Hullavators as far outboard as possible which means the kayaks clear the side of the car and wing mirrors without folding them in. I did have to modify one Hullavator to make the Hobie Lynx fit (36" wide Lynx = 36" max Hullavator width)

Click to Enlarge

Click to Enlarge

The Hullivator was for my wife to give her the option of loading and unloading by herself. It couldn’t be better. She now goes kayaking anytime she wants with little effort and no need for me to help her. Excellent product that’s worth every cent. Was super easy to install too.

Click to Enlarge

I have (2) Wilderness Systems Pungo 120 kayaks and was looking for something better that the cheap J-Shape kayak holders that I purchased elsewhere. Unless you are tall enough to lift the kayaks and install them from the side, the loading of a kayak on it's side is unwieldy and somewhat frustrating to keep the kayak from flipping to a horizontal position. I am using the factory racks with crossbars on my 2006 Toyota Highlander. I was looking for a solution that would allow me to load 2 kayaks with the keel down. Using a large bath mat to protect the paint I was able to load the kayak by myself and I am 5'6". The one thing that they could improve is that the rubber pads on the wings are very tacky. Once that you set the kayak onto the wings, the kayak will not move back and forth. You will find it very hard to move the kayak front to back once it is set in the cradle. This is a good thing since the kayak could slide off should a strap fail. The Pungo 120 has multiple angles so the contact with the wings are very minimal. The rubber does keep it in place before strapping them down. Once you load the kayak onto the wings, it will stay where it is.. it is a kind of a struggle to move the kayak.. a solution is to throw large beach towel on the wings before loading your kayak and you can position the kayak with ease. Once you have centered your kayak, lift the kayak one end at a time and remove the towel. Bow and stern tie downs are necessary to completely secure your kayak. The wings are 28" across and will rise 6" above your crossbars that you attache them to.

Click to Enlarge

Click to Enlarge

Bought two sets for two boats. Installed on a 2020 Forester and will be able to carry two boats side by side. Sturdy racks and easy to assemble and install and will be easy to remove when not in use. They will also fit on truck racks so the ease of install/removal will be a real plus. Side by side mount on this vehicle required placing the racks a little more outboard than I like but should not cause any problems. I will strap the boats to the crossbars as suggested in the instructions for additional stability. PS. one set was returned merch. Got a better price and can't tell that it was ever out of the box. Yay me.

Click to Enlarge

Click to Enlarge

I need replacements when a pair of Dockgrips was was lost or stolen. When others were stocked out, etrailer came through. Fast shipping and courteous service!

The Thule DockGlide Kayak Carrier and the Tie-Downs that came with it are a very functional High Quality Product. Once the DockGlide Carrier was properly positioned on the Cross bars it attached easily and solidly with the associated hardware. The Kayak slides on and off the Carrier very easily and is quite secure once properly tied down. I enjoy Kayaking and the DockGlide Kayak Carrier enables me to get where I want to go.

I acquired a second kayak and needed a system to fit the factory racks on my 2011 Toyota RAV4. Etrailer.com has always had information on what fits and has always had the item needed for the job. I attached the Yakima BigStack to the top with ease, and, with one other person to hold the kayaks while I secured, tied two of them down for a long road trip to Northern Minnesota. The system worked just fine. The only caveat was in the configuration of multiple boats in the instructions. The diagram has two boats on the same side of the posts, however, I found it more secure to put one on either side ( other reviews of this product on different Internet sites have found similar results.) The boats made it through the trip with no shifting.

Worked great on our Subaru Crosstrek with factory crossbars. Loading very easy, and it was very secure, for our 2 kayaks. The Yakima Big Sticks are easy to install/setup and take off. Very happy with our investment,