# 1
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
Very nice hitch. This is my third hitch purchase from etrailer.com and as usual, delivery was fast and the install went smoothly. The videos and user comments were very helpful. My vehicle is a few years old so the suggestion to chase the 8 mounting nut holes was spot on. There was a lot of mud and dirt which easily came out but would have been a pain to do while mounting the hitch. Also, the suggestion to spray down the rubber exhaust hangers and muffler heat shield bolts with penetrant (WD40) helped as well. The recommended draw bar and 4-wire harness also mounted beautifully. Got to love those factory installed rear wire harnesses which allow plug-in trailer harnesses on the Honda/Acura products. Total install took about 90 minutes which I think will be typical for a DIY'er who sprays down the bolts, chases the holes and without rushing or using air tools. Will buy again from etrailer.com
Product came in very quickly. Order was accurate. Website was very very easy to use. The instructions look super easy and the website even has a video in case I need assistance. Thank you etrailer.
# 2
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
I am using the hitch for a car dolly and a bike rack. The fit is a little loose for the bike rackmI'll see it really works when get on the road.
Quality is excellent. However, it did not work so I am not sure what to do with it. I thought I could use the top hitch for a Bike rack and pull a utility trailer with other toys. The trailer is too close to make a turn so good try but not able to use it. Thank you for asking. I did not open the box for a while because I was having the trailer worked on so assumed I waited too long to return.
# 3
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
Very nice hitch. This is my third hitch purchase from etrailer.com and as usual, delivery was fast and the install went smoothly. The videos and user comments were very helpful. My vehicle is a few years old so the suggestion to chase the 8 mounting nut holes was spot on. There was a lot of mud and dirt which easily came out but would have been a pain to do while mounting the hitch. Also, the suggestion to spray down the rubber exhaust hangers and muffler heat shield bolts with penetrant (WD40) helped as well. The recommended draw bar and 4-wire harness also mounted beautifully. Got to love those factory installed rear wire harnesses which allow plug-in trailer harnesses on the Honda/Acura products. Total install took about 90 minutes which I think will be typical for a DIY'er who sprays down the bolts, chases the holes and without rushing or using air tools. Will buy again from etrailer.com
Product came in very quickly. Order was accurate. Website was very very easy to use. The instructions look super easy and the website even has a video in case I need assistance. Thank you etrailer.
# 4
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
I have a custom made tow guard. The ball mount I have was too short to allow me to attach the tow guard to my new truck. I searched the web and found just what I needed at etrailer.com. It's the only site I found that carried the size I needed. The product fits my needs perfectly. I can now protect my boat from rocks and other road debris when towing. Thank you etrailer.com.
# 5
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 9-1/4" Long - 7,500 lbs
I've been using my etrailer hitch and wiring harness flawlessly for a year now. Great products, easy installation, no worries.
# 6
Ball Mount 3/4" Rise or 2" Drop - 12-5/8" Long
I've been using my etrailer hitch and wiring harness flawlessly for a year now. Great products, easy installation, no worries.
# 7
Convert-A-Ball Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10,000 lbs
Makes for a great hard-core dirt road set up with a 3000 pound trailer, in conjunction with the Curt rocker ball, Towing with an F150 over many miles of washboards, down through washes where the road was washed out, etc. Really makes for a gentler set up on the equipment in the trailer and the truck. Thanks a lot E-trailer!
My usage of your hitch is a bit unusual, I think. I pull a two ton roller with my Ram and I've used your cushioned hitch to smooth out the process. The roller Lunette just dropped over a 2" ball and then banged and jerked on the ball neck. Check out the photos for my adaptation.. I can flip it over and use the 2" ball! Have enclosed some photos. The cushion is holding up very well and it takes a beating!! Thanks
# 8
Curt Channel Style Adjustable Ballmount - 5-1/4" Rise, 6-3/4" Drop - 6,000 lbs
New GMC AT4 required a new ball mount and this one fit all the requirements for the truck and new multi-pro tailgate. With the AT4, I needed more drop and a longer shank (12" hole) for the tailgate to not hit my trailer jack stand; plus, the multiple drop adjustments will make changing trailers a snap. Great product from Curt and great service from etrailer (as usual).
This is a great ball mount. Fits the Class III hitch on my Explorer perfectly. Works well with my locking anti-rattle pin. However, there is a little noise from the dual pins used for the adjustment. I called etrailer’s customer service to inquire about remedies for this and was told that there is an Allen key adjustment that needs to be tightened to reduce the noise. I have yet to tighten it but other than that, the ball mount has done a great job.
# 9
MaxxTow Ball Mount w/ 2" Accessory Receiver - 2" Hitches - 2-1/4" Drop - 5,000 lbs
Heavy duty , very good quality.
# 10
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 14-1/4" Long - 6,000 lbs
I've been using my etrailer hitch and wiring harness flawlessly for a year now. Great products, easy installation, no worries.
# 11
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
I installed this on my 2015 Honda Accord for the purpose of pulling my small aluminum fishing boat and trailer. Works great!
Drawbar looks great and will be using in next two days. Thanks!
# 12
Brophy Ball Mount - 1" Rise, 2" Drop - 9-3/4" Long - Aluminum - 8,000 lbs
This stinger fits perfectly with my boat trailer and pickup. Having a bad back, the reduced weight is very helpful when removing and installing my Rock Tamer mud flaps. Shawnee was a huge help in determining what would work best for my application!!!
Very nice ball mount. Smooth, one piece design. Unlike my previous ball mount, it's long enough (enough straight length between the pin hole and the beginning of the bend) to accommodate a Blue Ox Hitch Receiver Immobilizer II, yielding a nice, tight connection. Attractive polished finish. Made in Taiwan (according to the box it came in). Photos show it attached to a Hidden Hitch Class III Hitch Receiver, secured with a Blue Ox Hitch Receiver Immobilizer II, and a Curt 40053 2-inch stainless steel ball.
What our customers are saying:
"i ordered on a tuesday and recieved my order on wednesday. very fast service and much cheaper than local auto parts stores"