# 1
Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
Excellent 2" ball mount. I have one of these for every vehicle that I use for towing.
Feels great in hand, but I won't be using it. For my 2006 Odyssey I need a 4" lift so my brother has already claimed it. Made in the USA.
# 2
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
I have never regretted ordering through etrailer. As always, this order arrived precisely on-time. The wiring for trailer lights proceeded exactly as expected. The online video describing the installation was very helpful with no surprises encountered while following the instruction. Don't forget to order a hitch pin. Surprisingly, it wasn't included with the drawbar.
The bar was exactly as I expected, but there were two deep dings that penetrated the paint and actually deformed the underlying metal. Disappointing as this is, knowing that it will probably develop rust prematurely while in use, I decided to not go through the hassle of requesting a replacement unit.
# 3
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
Very please with the purchase. Solid construction and raised the overall height of the receiver hitch on my Honda Odyssey with added ground clearance. Excellent service/shipping from eTrailer as usual.
I am using the hitch for a car dolly and a bike rack. The fit is a little loose for the bike rackmI'll see it really works when get on the road.
# 4
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 14-1/4" Long - 6,000 lbs
This long-shaft ball mount enabled me to fully insert and pin the shaft and get the rise I needed for towing level a Yakima Trailer by a 2015 Honda Odyssey. The typical, shorter shaft was not long enough for complete insertion and pinning of the shaft because the welded on arm-support piece hit the bumper.
This was part of the entire "Hitch System" I ordered for eTrailer. Everything fit together without any problems. Feel to this particular part is heavy and well over-designed to ensure performance and safety. Very confident that it will last long after the vehicle it is connected to is gone.
# 5
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
I have a custom made tow guard. The ball mount I have was too short to allow me to attach the tow guard to my new truck. I searched the web and found just what I needed at etrailer.com. It's the only site I found that carried the size I needed. The product fits my needs perfectly. I can now protect my boat from rocks and other road debris when towing. Thank you etrailer.com.
# 6
Curt Towing Starter Kit for 2" Hitches - 2" Ball - 3/4" Rise, 2" Drop - 7.5K
Seems to be high quality.
# 7
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 9-1/4" Long - 7,500 lbs
This was part of the entire "Hitch System" I ordered for eTrailer. Everything fit together without any problems. Feel to this particular part is heavy and well over-designed to ensure performance and safety. Very confident that it will last long after the vehicle it is connected to is gone.
This long-shaft ball mount enabled me to fully insert and pin the shaft and get the rise I needed for towing level a Yakima Trailer by a 2015 Honda Odyssey. The typical, shorter shaft was not long enough for complete insertion and pinning of the shaft because the welded on arm-support piece hit the bumper.
# 8
Curt Fusion Ball Mount for 2" Hitches - 1-7/8" Ball - 2" Rise - 5,000 lbs
Fits snug with the built-in tapers. Seems sturdy. Hopefully will last a long time.
Exactly what i ordered and it came fairly quickly! Im very happy worh everything!
# 9
Curt Towing Starter Kit for 2" Hitches - 2" Ball - 2" Rise, 4" Drop - 7.5K
Seems to be high quality.
Very convenient kit. Nice to have the locking pin and receiver cover. I reversed to the 2" rise position since my 2016 Honda Odyssey already sits low to the ground.
# 10
Curt Ball Mount for 2" Hitches - 8" Rise, 9-1/4" Drop - 14" Long - 5K
This was part of the entire "Hitch System" I ordered for eTrailer. Everything fit together without any problems. Feel to this particular part is heavy and well over-designed to ensure performance and safety. Very confident that it will last long after the vehicle it is connected to is gone.
# 11
Curt Multi-Ball Adjustable Ball Mount for 2" Trailer Hitches
Picked up my teardrop in ABQ on 2/17/23, and the Curt ball mount lined up perfectly with no drop/rise, and the extra length gave clearance for my rear door mounted spare tire. This mount is a beast, and the "overbuilt" nature of it gave me confidence that my Bronco would tow the teardrop easily. I also got the Curt Echo wireless brake controller, which synced easily to my phone and was easy to install, set up, and use. Overall a great towing experience, thanks to etrailer and Curt!
Very versatile - can use it on both my vehicles that have very different hitch height. Clean welds, super solid. Weighs a LOT!
# 12
Curt Class III Ball Mount with 1-7/8" Ball - 2" Drop - 3,500 lbs
This was part of the entire "Hitch System" I ordered for eTrailer. Everything fit together without any problems. Feel to this particular part is heavy and well over-designed to ensure performance and safety. Very confident that it will last long after the vehicle it is connected to is gone.
This long-shaft ball mount enabled me to fully insert and pin the shaft and get the rise I needed for towing level a Yakima Trailer by a 2015 Honda Odyssey. The typical, shorter shaft was not long enough for complete insertion and pinning of the shaft because the welded on arm-support piece hit the bumper.
# 13
Ball Mount 3/4" Rise or 2" Drop - 12-5/8" Long
This was part of the entire "Hitch System" I ordered for eTrailer. Everything fit together without any problems. Feel to this particular part is heavy and well over-designed to ensure performance and safety. Very confident that it will last long after the vehicle it is connected to is gone.
This long-shaft ball mount enabled me to fully insert and pin the shaft and get the rise I needed for towing level a Yakima Trailer by a 2015 Honda Odyssey. The typical, shorter shaft was not long enough for complete insertion and pinning of the shaft because the welded on arm-support piece hit the bumper.
# 14
Curt Tri-Ball Mount - 3 Chrome Balls - 10,000 lbs
Excellent product! With the three different ball sizes, this tri-ball mount gives you a lot of flexibility. Gone are the days of having several different ball mounts to fit different tongues. High quality construction makes this an excellent investment.
definitely solid as a rock
# 15
Curt Class II Drawbar - 5" Rise - 9-5/8" Long - 3,500 lbs
Great instructions and video on this website. The item was ship right away.
Looks like the picture - I'm happy.
# 16
Curt Ball Mount - 6" Rise, 8" Drop - 11-1/2" Long - 5,000 lbs
This was part of the entire "Hitch System" I ordered for eTrailer. Everything fit together without any problems. Feel to this particular part is heavy and well over-designed to ensure performance and safety. Very confident that it will last long after the vehicle it is connected to is gone.
This long-shaft ball mount enabled me to fully insert and pin the shaft and get the rise I needed for towing level a Yakima Trailer by a 2015 Honda Odyssey. The typical, shorter shaft was not long enough for complete insertion and pinning of the shaft because the welded on arm-support piece hit the bumper.
# 17
Curt Class III Ball Mount with 2" Ball - 4" Drop - 2" Rise - 7,500 lbs
Received product in perfect condition and was delivered on time as stated at purchase.
Great bit of kit.
# 18
Curt Ball Mount w/ Sway Control Tab for 2" Hitches - 3/4" Rise, 2" Drop - 7,500 lbs
I cannot use this ball mount because the shaft is too short that goes into hitch receiver on my one ton Dodge truck. It does not allow enough room between truck back bumper and ball to allow any trailer tongue to be put on ball.
Purchased this hitch as a companion for our Reese anti sway control. The small ball for the Reese sway control fits in the bracket and the 2” drop on the hitch is exactly what we needed to have our Jayco camper level when towing.
What our customers are saying:
"These guys were great! I placed my order and within a few hours it was shipped. The free shipping was a life saver, and they beat out other online retailers by upwards of $50. Great experience."